| English
14
NOTE:
In case the gear shift lever will not engage the de
-
sired gear, stop the engine. Then pull the clutch le-
ver and manually move the tiller slightly back and
forward in order to reposition the gears inside the
gearbox.
STOPPING THE UNIT
To stop the machine:
1.
Lower the engine speed by moving the throttle
lever to the “L” position.
2.
Release the clutch lever to stop the tiller from
moving.
3.
Move the gear shift lever to neutral position.
4.
Move the ON / OFF switch to the “OFF” posi
-
tion.
5.
Move the fuel valve lever to the “OFF” position.
MAINTENANCE AND CLEANING
WARNING:
Never do maintenance or cleaning with the unit run
-
ning. Always work on a cool unit. Before cleaning or
doing maintenance work, disconnect the spark plug
cap and read the relevant instructions. Always wear
proper clothing and protective gloves whenever
your hands are at risk.
Any adjustments or maintenance operations not
described in this manual must be carried out by
your Dealer or a specialized Service Centre with
the necessary knowledge and equipment to en
-
sure that the work is done correctly maintaining
the machine’s original safety level. Any operations
performed in unauthorized centers or by unqual
-
ified persons will totally invalidate the Warranty
and all obligations and responsibilities of the
Manufacturer.
Keep all nuts and screws tight to be sure the ma
-
chine is always in safe working condition. Routine
maintenance is essential for safety and for main
-
taining a high-performance level.
WARNING:
Never use the machine with worn or damaged parts.
Faulty or worn-out parts must always be replaced
and not repaired. Only use original spare parts.
MAINTENANCE SCHEDULE
Items
B
ef
o
re e
ac
h u
se
A
ft
er 1
st m
o
nt
h o
r 5
hr
s o
f
op
er
at
ion
Ev
er
y 3 m
o
nt
hs o
r 2
5h
rs
of
op
er
at
ion
Ev
er
y 6 m
o
nt
hs o
r 5
0
hr
s
of
op
er
at
ion
Ev
er
y 1
2 m
o
nt
hs o
r 1
0
0
hr
s
of
op
er
at
ion
Complete
unit
Visual
Inspection
√
Secure
fasteners
√
Control
handles
Check
√*
Frequency
Items
B
ef
o
re e
ac
h u
se
A
ft
er 1
st m
o
nt
h o
r 5
hr
s o
f
op
er
at
ion
Ev
er
y 3 m
o
nt
hs o
r 2
5h
rs
of
op
er
at
ion
Ev
er
y 6 m
o
nt
hs o
r 5
0
hr
s
of
op
er
at
ion
Ev
er
y 1
2 m
o
nt
hs o
r 1
0
0
hr
s
of
op
er
at
ion
Tilling tines
and knives
Check
√*
Εngine oil
Check -
Refill
√
Replace
√
√
Gearbox oil
Check -
Refill
√
Replace
√**
Linkages
Lubricate
√
Air filter
Check-
Clean
√*
√*
√*
Replace
√
Spark plug
Check -
Adjust
√*
Replace
√
Drive Belt
Replace
√**
Fuel filter
Clean
√
Fuel tube
Check
√*
Fuel sedi
-
ment cup
Clean
√
Valve clear
-
ance
Check -
Adjust
√**
*These items should be replaced if needed.
**These items should be maintained and repaired only by
authorised dealer, that have the appropriate tools and the
required mechanical.
TILLING TOOL
Periodically check tilling tines for wear or damage.
Damaged parts must be replaced before operating
the tiller again. Tilling knives wear will negatively af
-
fect tilling capability of the machine and they should
be replaced if required.
CLUTCH AND THROTTLE LEVER PLAY
Small adjustments on the already pre-assembled
clutch and throttle cables can be done by using the
nut and rod screw on each cable at the side of the
lever. The clutch lever free play should be as shown
in Fig. 10. If the travel distance in not correct, loose
the lock nut and adjust by play by turning the ad
-
justment bolt as required. When finished, tighten
the lock nut and check again for proper clutch lever
operation.
After any related adjustment, make sure that the
clutch or throttle levers move from one position to
another without the need for excessive force and
that the clutch or throttle rods on the gearbox or en-
gine respectively can be operated to their full range.
NOTE:
It is recommended that such adjustments are only
performed by trained personnel at your nearest deal
-
Frequency
GTL 900 PLUS
