F.F. Group ELM 32/1000 EASY, Original Instructions Manual

Page: 12 / 68

| English 12 ELM 32/1000 EASY
TECHNICAL DATA
Article Number 42 412
Model ELM 32/1000 EASY
Voltage
V 220-240
Hz 50
Rated Power Input W 1.000
No Load Speed min -1 3.400
Cutting width mm 320
Cutting height mm 20,40,60
Collector Capacity L 25
Weight Kg 6,2
Sound emission values determined according to
EN 60335-1, EN 60335-2-77
Typically the A-weighted noise levels of the product are:
Sound pressure level dB(A) 82,5
Guaranteed sound
power level
dB(A) 96
Uncertainty K dB 2,5
Vibration total values a
h
(triax vector sum)
and uncertainty K determined according to EN
60335-1, EN 60335-2-77
Vibration level max:
a
h ,HD
m/s
2
1,742
K m/s
2
1,5
IDENTIFICATION
1. Switch box
2. Switch lever
3. Extension cord restrain hook
4. Cable clip
5. Grass collector
6. Collector flap
7. Upper handle
8. Lower handle
9. Motor housing
10. Rear wheels
11. Front wheels
12. Grass indicator flap
ASSEMBLY
f
Put the cable hook on the upper handle, close to the
starting point (B) .
f
Connect upper and lower handles with supplied
screws and knobs (C) .
f
Insert the handles into the mower body and tighten
the fixed screws (D) .
f
Clip the cable clip on the handle. Clip the cord into
the cable clip (E) .
GRASS COLLECTOR ASSEMBLY AND FITTING
The grass collector (5) prevents grass clippings
being thrown across your lawn as you mow.
1. Insert the grass collector handle into the holes
on the top of grass collector until it clicks in (F) .
2. Align the upper and lower grass collector sec-
tions and join. Ensure the clips are located cor-
rectly and securely (G) .
3. Fix the supporting rod by inserting the edges
into the holes (f1) and after push the sides into
the slots (f2) on both sides of the bag (F) .
4. Clip the protective plastic straps onto the sup-
port rod of the grass collector (H) .
5. Lift the collector flap (6) with one hand. With
the other hand hold the grass collector by the
handle and hook it in from above (J) .
OPERATION
WARNING! Before connecting to the mains supply,
always check the switch is in the off position!
EXTENSION CORD RESTRAINT (S)
We recommend using your mower as outlined in
this section to achieve optimum results and to re-
duce the risk of cutting the mains cable. Place the
bulk of the mains cable on the lawn, close to the
starting point. Feed the cable through the cable
restraint (3) .
ADJUSTING THE CUTTING HEIGHT (K, L)
This electric lawn mower is equipped with a 3-po-
sition height adjustment system. To obtain the
desired cutting height, the front and rear axles
are repositioned on the underside of the mower
housing.
WARNING! Disconnect the mower from the power
supply and ensure the blade has stopped coast-
ing before adjusting the height.
1. To adjust the front wheel cutting height posi-
tion (K)
a. Turn the mower upside down.
b. Pull the wheel axle towards the front of the
mower.
c. Locate the wheel axle into the desired cut-
ting height adjustment position.
Note: Make sure that both front right and left
wheel are located in the same cutting height ad-
justment position.
2. To adjust the rear wheel cutting height position
(L)
a. Turn the mower on its side.
b. Pull the rear wheel axle towards the mow-
er’s collector flap.
c. Locate the wheel axle into the desire cutting
height adjustment position.
STARTING THE MOTOR
1. Plug the machine into the electric supply, ensur-
ing it meets the recommended requirements.
Electrical power should be supplied via a residual
current device (RCD) with a tripping current of
not more than 30 mA.
2. Before starting the lawn mower, hold the handle
assembly with both hands and tilt the handle