F.F. Group ELC 40/2400 PLUS, Original Instructions Manual

Page: 14 / 84

| English 14 ELC 40/2400 PLUS
CONNECTION TO THE POWER SUPPLY
Make sure the power supply information on the ma-
chine’s rating plate are compatible with the power
supply you intend to connect it to.
This appliance is Class II* and is designed for connec-
tion to a power supply matching that detailed on the
rating label and compatible with the plug fitted. If
an extension lead is required, use an approved and
compatible lead rated for this appliance. Follow all
the instruction supplied with the extension lead.
*Double insulated: This product requires no
earth connection as supplementary insulation
is applied to the basic insulation to protect
against electric shock in the event of failure of
the basic insulation.
GUIDELINES FOR USING EXTENSION CORDS
f
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage resulting in loss of power and overheating.
f
Always replace a damaged extension cord or have it
repaired by a qualified person before using it.
f
Protect your extension cords from sharp objects,
excessive heat and damp/wet areas.
f
Use a separate electrical circuit for your tools. This
circuit should be protected with the appropriate
time-delayed fuse. Before connecting the motor to
the power line, make sure the switch is in the OFF
position and the electric voltage is rated the same
as the voltage stamped on the motor nameplate.
Running at a lower voltage will damage the motor.
PRODUCT SPECIFICATIONS
INTENDED USE
The power tool is intended for sawing wood such as
wooden beams, planks, branches, tree trunks, etc.,
and for sawing of trees. Cuts can be sawed with or
across the grain. This power tool is not suitable for
sawing mineral materials.
TECHNICAL DATA
Article Number 42 410
Model ELC 40/2400 PLUS
Voltage
V 230
Hz 50
Rated power input W 2.400
No load speed rpm 7.600
Chain speed (no-load) m/s 13,5
Blade length mm 405
Cable m 0,25
Oil reservoir capacity ml 150
Weight Kg 6,3
Chain bar Model (160SDEA041) 405mm
Chain type (91PJ056X) 405mm
Sound emission values determined according to
EN 60745-1, ΕΝ 60745-2-13
Typically the A-weighted noise levels of the product are:
Sound pressure level dB(A) 95,92
Guaranteed sound
power level
dB(A) 106,92
Uncertainty K dB 2,5
Vibration total values a
h
(triax vector sum)
and uncertainty K determined according to EN
60745-1, ΕΝ 60745-2-13
Vibration level max:
a
h ,HD
m/s
2
4,3
K m/s 2 1,5
IDENTIFICATION
1. Rear handle
2. On/Off switch
3. Lock-off button for On/Off switch
4. Oil filler cap
5. Activation lever for kickback brake (hand guard)
6. Front handle
7. Cover
8. Locking knob
9. Chain-tensioning ring
10. Chain bar
11. Saw chain
12. Chain guard
13. Power plug
14. Gripping teeth
15. Drive sprocket
16. Fastening bolt
17. Oil outlet
18. Guide fin for chain bar
19. Oil level gauge
20. Ventilation slots
21. Chain tensioning gear
22. Strain relief bracket
PREPARING FOR USE
DANGER! To avoid serious personal injury, do
not operate the chainsaw without the chain
bar, saw chain, and side cover properly as-
sembled.
WARNING: Do not attempt to operate the
chainsaw if any part is damaged or missing.
WARNING: An electric power tool that is
plugged in can start accidentally. Unplug the
chainsaw before preparing for use or per-
forming maintenance.
CHECKING THE FRONT HAND-GUARD POSITION (H)
After unpacking the chainsaw, check the position of
the front hand-guard. The chainsaw will not run with
the chain brake engaged. Pull the front hand-guard