F.F. Group CS 65/1500 PLUS, Manual

Page: 10 / 56

| English 10 CS 65/1500 PLUS | CS 85/2000 PLUS
5. Raise the lower guard 15 by using the lever for
lower guard 1 , and then remove the saw blade.
6. Clean the saw blade flanges, then mount the new
saw blade onto the output spindle and against the
inner flange.
7. Make sure the saw teeth and arrow on the blade is
to be the same direction as the arrow on the lower
guard.
8. Reinstall the outer flange, and tighten the blade
clamp bolt.
9. Make sure that the saw blade runs freely by turn -
ing the blade by hand.
Depth adjustment (5)
1. Loosen the lock lever for depth adjustment 21 .
2. Hold the baseplate flat against the edge of the
work piece and lift the body of the saw until the
blade is at the right depth determined by the
depth of cut scale 20 (align the scale line).
3. Tighten the lock lever for depth adjustment.
Angle adjustment (6)
1. Loosen the Lock knob for angle adjustment 9 .
2. Adjust the shoe to the desired angle between 0° to
45°. [See miter scale 8 ].
3. Tighten the lock knob for angle adjustment.
Switch on and off (7)
Before engage the ON/OFF switch, check that the
saw blade is properly fitted and run smoothly, the
blade clamp bolt is well tightened.
1. Connect the plug to the power supply, the pow -
er-on indicator 5 is illumed until the tool discon -
nect from the power mains.
2. To switch on the circular saw, press the lock-off
button 18 and pull the ON/OFF switch trigger 17 .
3. When you release the switch trigger 17 , the tool
turns off.
Parallel cut adjustment (8)
1. Loosen the lock knob of edge guide 10 .
2. Slide the parallel guide 12 through the slots in the
shoe to the desired width.
3. Tighten the lock bolt to fit it in the position.
4. Ensure that the edge guide rests against the wood
along its entire length to give a consistent parallel
cuts.
Laser line generator (7)
Warnings: Do not stare directly at the laser beam,
do not deliberately aim the beam at personnel and
ensure that it is not directed towards the eye of a per -
son for longer than 0.25s. When you make the line
of the cut on the work piece, the laser line generator
can help you get better alignment.
Turn on: Press the laser generator switch 4 , the laser
generator 7 works.
Turn off: Press the switch again.
1. Check that the laser line aligns with the cutting
line as marked on the workpiece.
2. Adjust the angle of cut as required
3. Plug in the machine and start the motor
4. When the blade is at its maximum speed (approx -
imately 2 seconds), place the saw on the work-
piece.
Protection class
/ II
Sound emission values determined according to
EN 62841-1, EN 62841-2-5
Typically the A-weighted noise levels of the
product are:
Sound pressure
level
dB(A) 96,6 93,4
Sound power
level
dB(A) 107,6 104,4
Uncertainty K dB 3 3
Wear hearing protection!
Vibration total values a
h
(triax vector sum)
and uncertainty K determined according to
EN 62841-1, EN 62841-2-5
Vibration total values:
a
h
m/s
2
3,37 4,73
K m/s
2
1,5 1,5
Functional Description:
1. Lever of lower guard
2. Dust extraction outlet
3. Saw blade (select models)
4. Laser generator switch (select model)
5. Power-on indicator (select models)
6. Auxiliary handle (select models )
7. Laser generator (select models)
8. Miter scale
9. Lock knob for angle adjustment
10. Lock knob for parallel guide
11. Baseplate
12. Parallel guide
13. Outer flange
14. Blade clamp bolt
15. Lower guard
16. Spindle lock button
17. ON/OFF switch
18. Lock-off button
19. Main handle
20. Depth of cut scale
21. Lock lever for depth adjustment
ASSEMBLY
Important: Prior to any assembly and adjustment al -
ways unplug the tool.
Changing the blade (3, 4)
Warning: Always disconnect the plug from the pow -
er mains before making any adjustment or attaching
any accessories.
1. Place this circular saw on its side on a flat surface.
Advice you bring the base plate down as a mini -
mum depth cut then it is ease to change the blade.
2. Push the spindle lock button 16 toward motor
housing as the arrow shows in image 3 and firmly
hold it.
3. Turn the blade clamp bolt 14 anti-clockwise by us -
ing the wrench that supplied with the tool.
4. Remove the blade clamp bolt 14 and outer
flange 13 .