Extron electronics TLP Pro x25M Series, Setup Manual, Page: 5 / 6

5
Product Category
A MENU Button (see figure 4 on the previous page)— Activates the setup menu (see Setup Menu on the next page).
B RESET Button — Pressing the Reset button allows the unit to be reset in any of three different modes (for an overview, see
Reset Modes
, on the next page).
C RESET LED
— Provides feedback about the reset status when the user presses the Reset button (see
Reset Modes
).
D Mounting Slots
— The TLP Pro 725M and TLP Pro 1025M have four, one in each corner. The TLP Pro 525M has two, one in each
top corner. The hooks on the corners of the mounting plate (see figure 1 , 3 on page 2) fit into these slots for wall mounting.
E Digital Input Monitoring Port — This two-pole captive screw port ( 1 = signal and G = ground) monitors digital input with or
without a +5 VDC pull-up.
F LAN/PoE Connector
— Connect the TouchLink panel to a PoE power injector (not provided) using a twisted pair cable,
terminated with an RJ-45 connector. Connect the power injector to the LAN through a nework switch. An Extron IP Link Pro
control processor must also be connected to the same network as the TouchLink Pro touchpanel. TLS models do not require a
control processor
ATTENTION:
• The TouchLink panels are Power over Ethernet (PoE 802.3af, class 3) compliant. Do not power on the touchpanels
until you have read the Attention in the “Rear Panel Features” section of the
TLP Pro 525, 725, and 1025 Series
User Guide .
• Les écrans TouchLink supportent l’alimentation via Ethernet (PoE 802.3af, classe 3). Veuillez lire la partie
« Attention » dans la section « Rear Panel Features » du
TLP Pro 525, 725, and 1025 Series User Guide , avant de
mettre sous tension les écrans tactiles.
NOTE:
These TouchLink panels are shipped without a power
injector. The power injector must be purchased separately.
Menu Button
Reset Button
Reset LED
Mounting Slots
Digital Input Monitoring Port
LAN/PoE Connector
Extron recommends the Extron XTP PI 100 power injector (see figure 5).
Your power injector may look different.
G USB Port — Compatible with USB 2.0.
H Speaker — Provides audible feedback for the user.
•
TLP Pro 525M and TLS 525M — a single speaker
•
TLP Pro 725M and TLS 725M
— a single speaker
•
TLP Pro 1025M and TLS 1025M
— two (dual mono) speakers
USB Port
Speaker
100-240V
~
50-60Hz
0.4A MAX
XTP
PWR
XTP PWR
To network switch To TouchLink panel
Figure 5.
XTP PI 100 Power Injector
figure 5
I Slot for Mounting Plate — The tongue at the bottom of the mounting plate (see figure 1 ,
4
) fits into this slot, for wall mounting.
J Mounting Screw — Tightens against the tongue of the mounting plate to secure the TouchLink panel.
K Rear Panel Status Lights — These lights can be disabled for glass mount applications.
•
TLP Pro 525M and TLS 525M
— no lights
•
TLP Pro 725M and TLS 725M
— Six lights, three on each side of the panel
•
TLP Pro 1025M and TLS 1025M
— Two lights, one on each side of the panel
TLS models — The LEDs light green when the room is currently available and red when the room is currently booked. They
cannot be programmed.
TLP Pro models — The LEDs can be configured to light red or green and to blink or light continuously, to provide system
feedback.
The rear panel status lights can be toggled between enabled and disabled by using the
Setup Menu
(see the next page).
For information about programming these LEDs for the TLP Pro x25M models, see the Global Configurator Help File and Global
Scripter Help File .
Mounting Screw
Slot for Mounting Plate
Rear Panel Status Lights