Extron electronics TLP 1000MV User Manual Download Page 18

Page: 18 / 54

LAN Connector
MTP Connector

Zip-tie Holder

Cable Runway

Figure 11.

Connecting and Securing Cables

Power connector

— connect the two pole, 3.5 mm captive screw connector from

the 12 VDC, 1.0 A power supply (not provided) to the power supply socket on the
rear panel. Ensure the connections have the correct polarity as shown below.

NOTES:

• Extron recommends using the Power over Ethernet power supply.

The 12 VDC, 1.0 A power supply should be used only for setup or

troubleshooting.

•

If both power supplies are connected to the TLP 1000TV, the PoE power

supply takes precedence.

Power Receptacle

DC Power Cord
Captive Screw Connector

AC Power Cord

Ground
+12 VDC

External

Power Supply

(12 VDC, 1 A )

SECTION A–A

Ridges

Smooth

Power Supply

Output Cord

3/16"

(5 mm) Max.

Figure 12.

Power Supply Connection

CAUTION:

See the

cautions

on page 8 for important information about power

supplies.

NOTE:

See the

notes

on page 8 for important information about wiring captive

screw connectors.

TLP 1000MV and TLP 1000TV • Panel Features

Summary of Contents for TLP 1000MV























































Search results

Summary of Contents for TLP 1000MV

Reviews:

Related manuals for TLP 1000MV

Brands by name

Popular brands

Extron electronics TLP 1000MV, User Manual

Search results

Summary of Contents for TLP 1000MV

Reviews:

Related manuals for TLP 1000MV

Brands by name

Popular brands