Extron electronics MVX VGA A User Manual Download Page 87

Page: 87 / 107

Matrix Software, cont’d

MVX VGA A Matrix Switchers • Matrix Software

5-6

PRELIMINAR

Updating firmware

The firmware upgrade utility provides a way to replace the firmware that is coded

on the switcher’s control board without taking the switcher out of service and

replacing the firmware IC chip.
Update the switcher firmware as follows:

Visit the Extron Web site, www.extron.com, click the

Download Center

tab,

and then click the

Firmware

link (figure 5-6).

Figure 5-6 — Location of firmware upgrade files

Select the appropriate firmware file (CrossPoint 300 Series/

MVX 128/1212/168/1616 VGA A) to download and click

Download

Enter the requested personal information and then click

Download

to copy the

firmware to your computer.

Click

Run

twice (figure 5-7). The PC downloads the firmware update from

the Extron Web site and starts the Extron Installation Program to extract the

firmware file.

Click

Next

. The program extracts the firmware files and places them in a

folder identified in the InstallShield Wizard window.

Note the folder to which the firmware file is saved.

Click

Finish

to exit the program.

Summary of Contents for MVX VGA A












































































































Search results

Summary of Contents for MVX VGA A

Reviews:

Related manuals for MVX VGA A

Brands by name

Popular brands

Extron electronics MVX VGA A, User Manual

Search results

Summary of Contents for MVX VGA A

Reviews:

Related manuals for MVX VGA A

Brands by name

Popular brands