Extron electronics MVX VGA A User Manual Download Page 59

Page: 59 / 107

Operation, cont’d

MVX VGA A Matrix Switchers • Operation

3-36

PRELIMINAR

Setting the front panel locks

(Executive

modes)

The matrix switcher has three levels of front panel security lock that limit the

operation of the switcher from the front panel:

•

Lock

mode 0 —

The front panel is completely unlocked. All front panel

functions are available.

•

Lock

mode 1 —

All changes are locked from the front panel (except for

setting

Lock

mode 2). Some functions can be viewed.

•

Lock

mode 2 —

Basic functions are unlocked. Advanced features are locked

and can be viewed only.

Basic features consist of:



Making ties



Saving and recalling presets



Setting input audio gain and attenuation



Changing Lock modes

Advanced features consist of:



Setting video and audio output mutes



Setting audio output volume



Setting the rear panel remote port protocol and baud rate

The switcher is shipped from the factory in

Lock

mode 2.

Selecting

Lock

mode 2 or toggling between mode 2 and mode 0

If the switcher is in

Lock

mode 0 or mode 1, this procedure selects mode 2.

If the switcher in in

Lock

mode 2, this procedure selects mode 0 (unlocks the

switcher).

To toggle the lock on and off, press and hold the Enter button, the RGBHV button,

and the Audio button simultaneously for approximately 2 seconds (figure 3-57).

RGBHV AUDIO

ENTER

RGBHV AUDIO

ENTER

I/O

Press and

hold the Enter, RGBHV, and Audio

buttons simultaneously to turn on

Lock

mode 2

or to toggle between mode 2 and mode 0.

2 seconds

The Enter, RGBHV, and
Audio LEDs blink

twice to

indicate the mode change.
Release the buttons.

I/O

Figure 3-57 — Toggle front panel lock on or off

Summary of Contents for MVX VGA A












































































































Search results

Summary of Contents for MVX VGA A

Reviews:

Related manuals for MVX VGA A

Brands by name

Popular brands

Extron electronics MVX VGA A, User Manual

Search results

Summary of Contents for MVX VGA A

Reviews:

Related manuals for MVX VGA A

Brands by name

Popular brands