Extron electronics MVX VGA A User Manual Download Page 81

Page: 81 / 107

Programmer’s Guide, cont’d

MVX VGA A Matrix Switchers • Programmer’s Guide

4-12

PRELIMINAR

Command/response table for SIS commands (continued)

Command

ASCII command

(host to switcher)

Response

(switcher to host)

Additional

description

Information requests

Information request

X2)

X2!

•A

X2)

X2!]

Request part number

X2@]

See appendix A for part
numbers.

There are two separate sets of Extron firmware on which the switcher can report: the controller firmware, which is the

overall control firmware, and the latest optional Extron firmware update, which is available at www.Extron.com.

Query controller firmware
version

X1!]

Example:

1.23

]

The factory-installed
controller firmware version
is 1.23 (sample value only).

Query controller firmware
version (verbose)

X1!

X1@

X1@]

Provide a detailed status of
the MVX controller firmware
and any firmware upgrade.
• The firmware that is

running is marked by an
asterisk (*).

• A caret (^) indicates that

the firmware has a bad
checksum or an invalid
load.

• ?.?? indicates that

firmware is not loaded.

Response description:

Controller firmware version-updated firmware version

]

Example:

Meaningless data
for this switcher model

Response:

Description

MVX firmware version

-1.00(1.06-16x16 Series -Wed, 22 Feb 2006 00:00:00 GMT)-1.00*(1.06-16x16 Series -Thu, 16 Mar 2006 16:39:21 GMT)

Updated firmware version

* indicates the version running

Upload date and time

Request system status

X2#

•

X2#

•

X2#

•

X2#

•

X2#

•

X2$]

Response description:

+3.3V

•+5V•-5V•+15V•-15V•te

mperature (degrees fahrenheit)

]

Example:

3.29•5.04•-5.14•15.27•-15.15•120.20

-15V power system at -15.15V

Temperature 120.20 degrees

3.3V power system at 3.29V

Summary of Contents for MVX VGA A












































































































Search results

Summary of Contents for MVX VGA A

Reviews:

Related manuals for MVX VGA A

Brands by name

Popular brands

Extron electronics MVX VGA A, User Manual

Search results

Summary of Contents for MVX VGA A

Reviews:

Related manuals for MVX VGA A

Brands by name

Popular brands