Extron electronics MVX VGA A User Manual Download Page 94

Page: 94 / 107

5-13

MVX VGA A Matrix Switchers • Matrix Software

PRELIMINAR

Master reset does not reset the Internet protocol (IP) settings.

Using

Emulation

mode

Emulation

mode allows you to set up the software without attaching the switcher to

the computer. To use

Emulation

mode, do the following:

Double-click the Matrix Switchers Control Program icon in the Extron

Electronics group or folder.

Choose

Emulate

, and click

Choose an emulation file to open, and click

. The file DEMO.MTX provides

a sample of a completed matrix setup. Selecting the file NEW.INI or clicking

Cancel

provides a blank setup to get you started.

Enter the file name under which you want to save any changes to the file, and

click

Select the number of video boards, audio boards, and matrix model for which

you are preparing a configuration, and click

Continue using the program as described beginning on page 5-3.

Using the help system

For information about program features, you can access the help program in any of

the following ways:

• From the Extron Electronics program folder or group, double-

click on the MATRIX S Help icon (shown at right).

• From within the Matrix Switcher Control Program, click on the

Help

menu on the main screen.

• From within the Matrix Switcher Control Program, press the F1 key.

Button-Label Generator Program

The Button Label Generator software creates labels that you can place in the

translucent covers above and below the front panel input and output buttons. You

can create labels with names, alphanumeric characters, or even color bitmaps for

easy and intuitive input and output selection. See appendix A, “Specifications,

Part Numbers, Accessories”, for the procedure for removing and replacing the

translucent covers.
The Extron Button Label Generator is available on the Extron Web site,

www.extron.com, under the Download Center tab. Click the

Software

link

(figure 5-13), and download and install the program.

Figure 5-13 — Location of software on the web site

The Button Label Generator software is also included on the Extron Software

Products CD-ROM that accompanies the switcher.

Summary of Contents for MVX VGA A












































































































Search results

Summary of Contents for MVX VGA A

Reviews:

Related manuals for MVX VGA A

Brands by name

Popular brands

Extron electronics MVX VGA A, User Manual

Search results

Summary of Contents for MVX VGA A

Reviews:

Related manuals for MVX VGA A

Brands by name

Popular brands