Extreme Networks Summit WMScanner Page 38 User Manual Download

Page: 38 / 217

WMScanner GUI and Menus

Summit WMScanner Users Guide

Advanced Sub-menu

The

Advanced

sub-menu provides functionality for modifying different aspects of a drawing, drawing

entities, and objects.

Building Manager

The

Building Manager

dialog box provides advanced functionality for managing and navigating floors in

the current drawing. Most users will not require these features.

Add Floor

Adds a new floor to the current drawing.

Remove Floor

Removes a selected floor from the current drawing.

Set as Current Floor

Sets a particular floor to the current floor and makes it visible.

Show Floor

Shows a selected floor.

Summary of Contents for Summit WMScanner


























































































































































































































Search results

Summary of Contents for Summit WMScanner

Reviews:

Related manuals for Summit WMScanner

Brands by name

Popular brands

Extreme Networks Summit WMScanner, User Manual

Search results

Summary of Contents for Summit WMScanner

Reviews:

Related manuals for Summit WMScanner

Brands by name

Popular brands