background image

pH300   V1.0    7/09 

Keypad Description 

 
The meter has five (5) front panel function keys: 
 

     ON/OFF Power Key 

 

   Calibration Key: 

a)  When taking a measurement, press this key to enter the calibration mode 
b)  When in the programming mode, press this key to change the displayed 

number or the ON/OFF state 

   Function Key 

a)  Press momentarily (< 1.5 seconds) to toggle between the two measurement 

parameters pH and mV 

b)  Press and hold for at least 2 seconds to enter the P1 programming parameter. 

Subsequent presses will scroll through the remaining parameters P2, P3… 

   Backlight and ENTER Key 

a)  In the measurement mode, momentary presses toggle the backlight on and off 
b)  When in the programming or calibration mode, press to ENTER data 

 

   MEMORY STORE and RECALL Key 

a)  In the measurement mode, momentary presses store the displayed readings. 

Press and hold for at least 2 seconds to recall a saved reading 

b)  In the programming mode, press to change the displayed number or the 

ON/OFF state 

 

Store, Recall, and Clear Datalogger Memory 

STORE Readings 

The meter can store up to 100 pH and 100 mV readings for a total of 200 data points. To 
store a reading, wait until the reading stabilizes (the smiling face icon 

 appears when the 

reading stabilizes). Press the 

M+/RM

 key momentarily to store a reading. The 

M+

 icon 

appears and the data point serial number increments. 

RECALL Readings 

In the measurement mode, press the 

M+/RM

 key to recall the most recently stored 

reading. 

RM

 and the data point serial number for the displayed reading will appear on the 

LCD. The measurement information will appear on the lower right hand side of the LCD. 
Use the 

CAL 

or 

M+/RM

 buttons to scroll the remaining stored readings. Press the 

ENTER

 

key to return to the normal measurement mode. 

CLEAR Readings 

From the RECALL mode, press and hold the 

ENTER

 key for at least five (5) seconds. The 

LCD display will show ‘CLR’ indicating that all of the stored readings have been erased. 
The unit will automatically return to the normal measurement mode after approximately 2 
seconds. 

www.burntec.com

Summary of Contents for pH300













Reviews: