background image

MN25 Version 2.2 Aug 2003 

2

Warranty 

EXTECH INSTRUMENTS CORPORATION warrants this instrument to be 
free of defects in parts and workmanship for one year from date of shipment 
(a six month limited warranty applies on sensors and cables). If it should 
become necessary to return the instrument for service during or beyond the 
warranty period, contact the Customer Service Department at (781) 890-
7440 ext. 210 for authorization or visit our website at www.extech.com (click 
on ‘Contact Extech’ and go to ‘Service Department’ to request an RA 
number). A Return Authorization (RA) number must be issued before any 
product is returned to Extech. The sender is responsible for shipping 
charges, freight, insurance and proper packaging to prevent damage in 
transit. This warranty does not apply to defects resulting from action of the 
user such as misuse, improper wiring, operation outside of specification, 
improper maintenance or repair, or unauthorized modification. Extech 
specifically disclaims any implied warranties or merchantability or fitness for 
a specific purpose and will not be liable for any direct, indirect, incidental or 
consequential damages. Extech's total liability is limited to repair or 
replacement of the product. The warranty set forth above is inclusive and no 
other warranty, whether written or oral, is expressed or implied. 

Introduction 

Congratulations on your purchase of Extech’s MN25Multimeter. 
This meter measures AC/DC Voltage, AC/DC Current, 
Resistance, Capacitance, Frequency, Duty Cycle, Temperature, 
Diode Test and Continuity. Proper use and care of this meter will 
provide many years of reliable service. 

Summary of Contents for MN25
















Reviews: