background image

1.5

SAFETY WARNING

IMPORTANT

ALWAYS READ THE USER MANUAL BEFORE OPERATION.
PLEASE CONFIRM THAT THE POWER SUPPLY STATED ON THE

PRODUCT IS THE SAME AS THE MAINS POWER SUPPLY IN YOUR
AREA.






This product must be installed by a qualified professional.
Always operate the equipment as described in the user manual.

A minimum distance of 0.5m must be maintained between the

equipment and combustible surface.
The product must always be placed in a well ventilated area.

Always make sure that the equipment is installed securely.

DO NOT stand close to the equipment and stare directly into the LED

light source.

Always disconnect the power supp ly before attempting and

maintenance.

Always make sure that the supporting structure is solid and can

support the combined weight of the products.

The earth wire must always be connected to the ground.
Do not touch the power cables if your hands are wet.

ATTENTION


This product left the place of manufacture in perfect condition. In

order to maintain this condition and for safe operation, the user must
always follow the instructions and safety warnings described in this
user manual.

Avoid shaking or strong impacts to any part of the equipment.

Make sure that all parts of the equipment are kept clean and free of

dust.

Always make sure that the power connections are connected correct

and

secure.

If there is any malfunction of the equipment, contact your distributor

immediately.

When transferring the product, it is advisable to use the original

packaging in which the product left the factory.

Shields, lenses or ultraviolet screens shall be changed if they have

become damaged to such an extent that their effectiveness is
impaired.

The lamp (LED) shall be changed if it has become damaged or

thermally deformed.

1 PRODUCT(GENERAL)

4

17

4 USING A DMX512 CONTROLLER

Ar1.d

BLUE

1

2

0

255

CHANNEL

FUNCTION

VALUE

3

4

0

255

0

255

0

255

GREEN

RED

MASTER DIMME R

HSV

1

2

0

255

CHANNEL

FUNCTION

VALUE

3

0

255

0

255

VALUE(0~100%)

SATURATION(0~100%)

HUE(0~100%)

Ar1.S

BLUE

1

2

0

255

CHANNEL

FUNCTION

VALUE

3

4

0

255

0

255

0

255

GREEN

RED

MASTER DIMME R

STORE

5

0

255

2011.6.2

2011.6.2

Summary of Contents for TourLED 42 CM IP33













Reviews: