background image

D MX512
C ONTROLLER

Example:

The figu re above shows a simple DMX layout
which h as use d thre e units at eac h DMX address.
The three units have differ ent ID addresses which
allows t he use r to co llectively control the who le
group o f units at that DMX address by setting
CH10 to 0, or to control each unit indep enden tly by
first selecting the DMX address and then by u sing
Ch10 to locate the t arget ID address.

7

2 INSTALLATION

............

DMX Addr.1
ID Ad dr.1

DMX Add r.1
ID Addr.2

DMX A ddr.1
ID Add r.3

DMX Ad dr.12
ID Addr.1

DMX A ddr.12
ID Add r.2

DMX Addr.12
ID Addr.3

】 【

】 【

】 【

Note: This product have three DMX512 channel configuration:

and

TOUR

,

Arc.1

,

Ar1.d

,

Ar1.s

HSV

4.1

BASIC ADDRESSING

Connect all of the units in series using standard DMX512 signal cable or

the IP65 rated cable

provided.

Set the DMX512 address in the

menu.

It is possible to have the same DMX address or independent

addresses for each fixture.

DMX

4.2

CHANNEL ASSIGNMENT

14

4 USING A DMX512 CONTROLLER

TOUR

USING A DMX512 CONTROLLER

1

2

0

255

3

4

0

255

0

255

0

255

CHANNEL

FUNCTION

VALUE

BLUE

GREEN

(or FADE TIME when CUS.01-CUS.10 in CH8 is activated)

RED

(or STEP TIME when CUS.01-CUS.10 in CH8 is activated)

MASTER DIMMER

5

WHITE1

3200K

WHITE2

3400K

WHITE3

4200K

WHITE4

4900K

WHITE5

5600K

WHITE6

5900K

171

200

201

205

206

210

211

215

216

220

221

225

226

230

RED100%/GREEN 100%P/BLUE100%/WHITE 100%

71

90

91

110

111

130

131

150

RED 0%/GREEN DOWN/BLUE 100%

RED UP/GREEN 0%/BLUE100%

RED100%/GREEN 0%/BLU EDOWN

RED100%/GREEN UP/BLUE UP

151

170

RED DOWN/GREEN DOWN/BLUE 100%

0

5

11

30

31

50

51

70

NO FUNCTION

RED100%/GREEN UP/BLUE0%

RED DOWN/GREEN 100%/BLUE0%

RED 0%/GREEN 100%/BLUE UP

COLOR MAC RO

2011.6.2

2011.6.2

Summary of Contents for TourLED 42 CM IP33













Reviews: