Expert Electronics ColibriDDC User Manual Download Page 64

Page: 64 / 69

ColibriDDC User Manual

RECEIVER OPERATIONS

Launch the receiver.

Wait 30 seconds, until the green LED stops blinking and will flash

yellow

Make sure that your net settings are set to automatically receive the IP address

Launch the ExpertSDR2 software and press the Opt ions button.

Set up your Device settings and press Search button, you'll see the window with an

available ColibriDDC receiver, press the Use button in front of it, save the settings.

Press the St art button in the ExpertSDR2.

B1:

Connect the receiver to PC with LAN-cable, supplied with the receiver

Set the static IP address 192.168.16.Х in Windows 7/8/10. Launch the receiver.

Launch the ExpertSDR2 software and press the Opt ions button

Set up your Device settings and press Search button, you'll see the window with an

available ColibriDDC receiver, press the Use button in front of it, save the settings

Press the St art button in the ExpertSDR2

B2:

If you have a local net with different IP address than 192.168.16.ххх and you need to change

the IP address of the receiver.

Connect the receiver to PC with LAN-cable, supplied with the receiver.

Set the static IP address in Windows 7/8/10. Launch the receiver.

Launch the ExpertSDR2 software and press the Opt ions button.

Change the ColibriDDC IP address.

Connect the receiver to the local net via the LAN-cable.

Now every PC in the local net can operate the receiver.

5.2

Remote operation

Over the following

link

you may find the manual which thoroughly describes how to operate the

ColibriDDC receiver remotely.

Summary of Contents for ColibriDDC






































































Search results

Summary of Contents for ColibriDDC

Reviews:

Brands by name

Popular brands

Expert Electronics ColibriDDC, User Manual

Search results

Summary of Contents for ColibriDDC

Reviews:

Brands by name

Popular brands