Expert Electronics ColibriDDC User Manual Download Page 25

Page: 25 / 69

ColibriDDC User Manual

ExpertSDR2 SOFTWARE DESCRIPTION

OFF - AGC is off.

LONG - preset with long AGC reaction (approximately 750 ms). Recommended for phone

modes.

SLOW - preset with slow AGC reaction (approximately 500 ms). Recommended for phone,

digital modes.

MED - preset with medium AGC reaction (approximately 250 ms). Recommended for CW,

digital modes.

FAST - preset with fast AGC reaction (approximately 100 ms). Recommended for CW, digital

modes.

USER - preset with custom AGC reaction (by default the slowest 1000 ms).

Note:

AGC settings influence the quality of the received signal. Be careful selecting the AGC preset
or tuning your own preset.

- St ep list allows to change the step of the mouse wheel in the range from 0.1

Hz to 100 kHz.

DSP functions:

- enable the RX equalizer (enabled on the picture).

- enable the TX equalizer.

- binaural audio mode (the phasing of the audio signal within the RX filter gives a stereo-

like effect).

- enable the adaptive Noise Reduction to clean the signal from noise interferences.

- enable the First Noise Blanker for impulse interference.

- enable the Second Noise Blanker for impulse interference.

Note:

The NB1 and NB2 algorithms are different. Try each of them to reach the best impulse
interference reduction. NB1 and NB2 Noise Blankers can be used simultaneously.

- enable Automatic Notch Filter for adaptive rejection of the narrowband interference in

the receiving band (interference, carrier signals, CW signals, etc.).

Note:

Summary of Contents for ColibriDDC






































































Search results

Summary of Contents for ColibriDDC

Reviews:

Brands by name

Popular brands

Expert Electronics ColibriDDC, User Manual

Search results

Summary of Contents for ColibriDDC

Reviews:

Brands by name

Popular brands