Expert Electronics ColibriDDC User Manual Download Page 12

Page: 12 / 69

ColibriDDC User Manual

HARDWARE DESCRIPTION

2.2

REAR PANEL DESCRIPTION

Name

Descript ion

6 SMA connector

“female”

Connector for HF and VHF antennas

7 BT (Boot) button

Button for the emergency firmware update.

8 EXT CTRL connector

Connector for controlling of the external devices

9 Reset IP address

button

Press to reset IP address and UDP

port of the receiver to default

state, IP: 192.168.16.200, port: 50001.

External reference

oscillator Input 10 MHz

10 MHz CMOS level

input

Appropriate Voltage amplitude for this input: 1...3 V Pk-to-Pk and

10 MHz frequency. Input impedance 2 kOhm.

Warning! Improper use or higher voltage may damage the

receiver!

2.2.1

Antenna

Before connecting the antenna, check the integrity of the antenna-feeder path.

For best results, the antenna should have an impedance of 50 Ohm to match the 50 Ohm

impedance of the receiver.

The antenna should have an SWR level not worse than 1.5:1. If the SWR is worse than 1.5:1,

match the cable and the antenna to the desired level.

Warning!

Always use E-t ype f errit e beads on ant enna and ot her cables, connect ed t o t he

receiver!

Summary of Contents for ColibriDDC






































































Search results

Summary of Contents for ColibriDDC

Reviews:

Brands by name

Popular brands

Expert Electronics ColibriDDC, User Manual

Search results

Summary of Contents for ColibriDDC

Reviews:

Brands by name

Popular brands