background image

 

18 

 

 

 

 

 

 

 

 

Step 9 

9A. Installing the Adjustable Boom to the Backrest Frame: 

Pull out and hold the 

Adjustable Boom Knob (11)

, and slide the 

Adjustable Boom (15)

 into the 

bottom of the 

Backrest Frame (10)

. Slide the 

Adjustable Boom (15)

 upwards until the desired 

height  is  visible  below  the 

Backrest  Frame  (10)

.  To  lock  the

  Adjustable  Boom  (15)

  in  place 

release  the 

Adjustable  Boom  Knob  (11)

.  Shift  the 

Adjustable  Boom  (15) 

inwards  until  the 

Adjustable Boom Knob (11)

 "POPS" down into the locked position. Make sure the 

Adjustable 

Boom Knob (11) 

is fully inserted. 

See Fig. E.

   

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Step 10 

10A. Attaching the Nylon Straps 

Attach the combined 

Long Nylon Strap (45) & Short Loop Strap

 

(44)

 to the 

Backrest Frame 

(10).

 This is done by hooking one end of the 

Safety Hooks 

on the

 Long Nylon Strap (45) 

to the

 

triangular 

tab  on  the  underside  of  the 

Backrest  Frame  (10)

.  Then  hook  the  other  end  of  the 

Safety Hooks 

on the

 Short

 

Nylon Strap (44)

 to the

 triangular tab

 on the 

Front Support Post 

(4)

 

 

 

 

ASSEMBLY 

Fig. E 

11 

11 

Summary of Contents for 4503

































Reviews: