EWM Taurus 401 Synergic S MM FKW Operating Instructions Manual Download | Manualshive

Page: 71 / 119

background image

Design and function

MIG/MAG welding

099-005339-EW501

31.01.2014

71

5.9.11

Standard MIG/MAG torch

The MIG welding torch trigger is essentially used to start and stop the welding process.

Operating elements

Functions

Torch trigger

• Start/stop welding

Other functions are also possible by tapping the torch trigger, depending on the machine type
and control configuration:

• Change over between welding programs (see "Program changeover with standard torches (P8)"

chapter).

• Program selection before starting welding (see chapter entitled "Selecting programs with the standard

torch trigger (P17)").

• Switching between wire feed units in dual operation mode (see chapter "single or double operation

setting (P10)")

5.9.12

MIG/MAG special-torches

Function specifications and more indepth information can be found in the operating manual for
the relevant welding torch!

5.9.12.1

Program- and Up- / down operation

Figure 5-36

Item Symbol

Description

0

1

Welding torch function changeover switch

(special welding torch required)

Changing over programs or JOBs

Infinite adjustment of welding performance.

5.9.12.2

Switching between Push/Pull and intermediate drive

DANGER

Do not carry out any unauthorised repairs or modifications!
To avoid injury and equipment damage, the unit must only be repaired or modified by
specialist, skilled persons!
The warranty becomes null and void in the event of unauthorised interference.

• Appoint only skilled persons for repair work (trained service personnel)!

CAUTION

Test!
Before re-commissioning, it is essential that an "inspection and test during operation"
is carried out conforming to IEC / DIN EN 60974-4 "Arc welding devices - inspection and
testing during operation"!

• For detailed instructions, please see the standard operating instructions for the welding

machine.

The plugs are located directly on the M3.7x printed circuit board.

Plug

Function

on X24

Operation with Push/Pull welding torch (factory setting)

on X23

Operation with intermediate drive

«
...
69
70
71
72
73
...
»

Summary of Contents for Taurus 401 Synergic S MM FKW
























































































































Reviews:

No comments

Related manuals for Taurus 401 Synergic S MM FKW

Brand: Wayne-Dalton Pages: 24

Brand: UniPOS Pages: 2

Brand: Nabco Pages: 50

Brand: Nabco Pages: 43

Brand: Nabco Pages: 10

Brand: Panasonic Pages: 152

Brand: Jensen Pages: 2

Brand: Jefferson Pages: 24

Brand: Image Dynamics USA Pages: 2

Brand: GANTERUD Pages: 24

Brand: HÜRNER Pages: 33

Brand: Gladen Pages: 2

Brand: EAW Pages: 2

Brand: Fireside Audiobox Pages: 12

Brand: Kogan Pages: 16

Brand: Dyna-Glo Pages: 9

Brand: jablotron Pages: 2

Brand: Beta Three Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands