EWM PHW 100 Operating Instructions Manual Download Page 34

Page: 34 / 36

Replaceable parts

PWH/PWM 100

099-008232-EW501

26.05.2020

10 Replaceable parts

The manufacturer's warranty becomes void if non-genuine parts are used!

• Only use system components and options (power sources, welding torches, electrode hold-

ers, remote controls, spare parts and replacement parts, etc.) from our range of products!

• Only insert and lock accessory components into the relevant connection socket when the ma-

chine is switched off.

10.1 PWH/PWM 100

Figure 10-1

Item

Order number

Type

Name

094-008237-00000 GASNOZZ SHORT D11mm

Gas nozzle, short

094-008238-00000 GASNOZZ SHORT D12MM

Gas nozzle, short

094-008240-00000 GASNOZZ LONG 9.5mm

Gas nozzle, long

094-008239-00000 GASNOZZ LONG 11mm

Gas nozzle, long

094-008281-00000 LENS LARGE PORED

Gas lens, coarse-pored

094-008242-00000 LENS PORED

Gas lens, fine-pored

094-009256-00000 PNOZZ 8-10 A 0,5 mm

Plasma nozzle

094-008282-00000 PNOZZ 15 A 0,6 mm

Plasma nozzle

094-008243-00000 PNOZZ PWH/PWM 100 20A 0.8

Plasma nozzle

094-008244-00000 PNOZZ PWH/PWM 100 25A 1.0

Plasma nozzle

094-008245-00000 PNOZZ PWH/PWM 100 30A 1.2

Plasma nozzle

094-008246-00000 PNOZZ PWH/PWM 100 40A 1.4

Plasma nozzle

094-008247-00000 PNOZZ PWH/PWM 100 50A 1.6

Plasma nozzle

094-008248-00000 PNOZZ PWH/PWM 100 60A 1.8

Plasma nozzle

094-008249-00000 PNOZZ PWH/PWM 100 70A 2.0

Plasma nozzle

094-009393-00000 PNOZZ 80 A 2.2 mm

Plasma nozzle

094-008250-00000 PNOZZ PWH/PWM 100 90A 2.4

Plasma nozzle

094-009394-00000 PNOZZ 95 A 2.6 mm

Plasma nozzle

094-008251-00000 PNOZZ PWH/PWM 100 100A 3.0

Plasma nozzle

094-009126-00000 PNOZZ 3.2mm

Plasma nozzle

094-009396-00000 PNOZZ LONG 0.5 mm

Plasma nozzle, long

094-009397-00000 PNOZZ LONG 0.6 mm

Plasma nozzle, long

094-008252-00000 PNOZZ LONG 0.8 mm

Plasma nozzle, long

094-008253-00000 PNOZZ LONG 1.0 mm

Plasma nozzle, long

094-008254-00000 PNOZZ LONG 1.2 mm

Plasma nozzle, long

094-008255-00000 PNOZZ LONG 1.4 mm

Plasma nozzle, long

094-008256-00000 PNOZZ LONG 1.6 mm

Plasma nozzle, long

094-008257-00000 PNOZZ LONG 1.8 mm

Plasma nozzle, long

094-008258-00000 PNOZZ LONG 2.0 mm

Plasma nozzle, long

Summary of Contents for PHW 100





































Search results

Summary of Contents for PHW 100

Reviews:

Related manuals for PHW 100

Brands by name

Popular brands

EWM PHW 100, Operating Instructions Manual

Search results

Summary of Contents for PHW 100

Reviews:

Related manuals for PHW 100

Brands by name

Popular brands