background image

EYE PROTECTION

Which conforms to ANSI/ CE specifications and provides protection against flying particles both from 
the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when 
connecting to air supply, loading, operating, or servicing this tool. Eye protection is required to guard 
against flying fasteners and debris, which could cause severe eye injury. The employer and/or user must 
ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements 
of the ANSI Z87.1 and 89/686/EEC, and provide both frontal and side protection.

BEFORE HANDLING OR OPERATING THIS TOOL

Read and understand the warnings contained in this manual.

Refer to “tool specifications” in this manual to identify the operating system on your tool.

OPERATION : 

TOOL OPERATION SYSTEM

NOTE

Non-side shielded spectacles and face shields alone do not provide adequate protection.

There are three available systems in these tools :

1. Contact Trip Operation 

(available system on : FN1850-CT, FS9040-CT, FS9240-CT)

 

The CONTACT TRIP MODEL tool contains a contact trip that operates in conjunction with the trigger to drive a fastener. To 
operate the tool in this manner, hold the tool with the contact trip pointing towards but not touching the work surface. Pull 
the trigger and then tap the contact trip against the work surface using a bouncing motion. Each depression of the contact 
trip will cause a fastener to be driven.

2. Sequential Trip

 

Operation

 

(available system on : FN1850-ST, FS9040-ST, FS9240-ST)

 

 

The SEQUENTIAL TRIP MODEL contains a contact trip that operates in conjunction with the trigger to drive a fastener. 
To operate a sequential trip tool, first position the contact trip on the work surface WITHOUT PULLING THE TRIGGER. 
Depress the contact trip and then pull the trigger to drive a fastener. As long as the contact trip is contacting the work and 
is held depressed, the tool will drive a fastener each time the trigger is depressed. If the contact trip is allowed to leave the 
work surface, the sequence described above must be repeated to drive another fastener.

3. Remote Fire 

(available system on : FN1850PAL, FS9040PAL, FS9240PAL)

 

The REMOTE FIRE MODEL is cycle by actuation of remote valve (RCVA3-F & TVA2-F) for mounted machines.

The operator must not hold the trigger on contact trip tools except during fastening operation, as serious injury could result 
if the trip accidentally contacts someone or something, causing the tool to cycle.

Keep hands and body away from the discharge area of the tool. A contact trip tool may bounce from the recoil of driving a 
fastener and an unwanted second fastener may be driven, causing injury.

WARNING  

WARNING  

15

Summary of Contents for FN1850





















Reviews: