evertz 570NAT-HW-X19 User Manual Download Page 54

Page: 54 / 56

570NAT-HW-X19

High Density Network Address Translator

Page - 44

Revision

1.0

4.11. CONFIGURATION MANAGEMENT TAB

The Configuration Management tab allows the user to export, edit and import each mode in a CSV file

format. The CSV file is useable in Microsoft Excel and allows for easy editing, saving and uploading file

using the

Browse

and

Upload

buttons.

Figure 4-33: WebEASY

- Configuration Management Tab

The current configuration for each currently used NAT type can also be exported from the 570NAT-X19-

10G by selecting

Download

beside the respective NAT configuration you wish to download. Doing so

will load a progress bar that, upon export will read ‘File Export Success’, at which time your browser’s file

download window will pop up. From here, users can save file to local disk or open the .csv file (note, this

is the browser download window and as such will vary by web browser)

Summary of Contents for 570NAT-HW-X19

























































Search results

Summary of Contents for 570NAT-HW-X19

Reviews:

Related manuals for 570NAT-HW-X19

Brands by name

Popular brands

evertz 570NAT-HW-X19, User Manual

Search results

Summary of Contents for 570NAT-HW-X19

Reviews:

Related manuals for 570NAT-HW-X19

Brands by name

Popular brands