evertz 570NAT-HW-X19 User Manual Download Page 38 | Manualshive

Page: 38 / 56

background image

570NAT-HW-X19

High Density Network Address Translator

Page - 28

Revision

1.0

Figure 4-11 : WebEASY® - IP NAT (Part 2 – WAN to LAN)

4.5.3. WAN to LAN: Input Flow Configuration

Flows 1 to 256

Mode:

This control allows the user to enable De-Encap/NAT or disable WAN to LAN for this flow.

Input Destination IP Address:

This control allows the user to set the Input Destination IP address of

the packets to be received.

Input Destination UDP Port:

This control allows the user to set the Destination UDP Port number to

be received.

VLAN:

This control allows the user to assign this flow to a VLAN.

SSM Filter:

This control allows the user to enable Source Specific Multicast (SSM) channel based

filtering.

«
...
36
37
38
39
40
...
»

Summary of Contents for 570NAT-HW-X19

























































Reviews:

No comments

Related manuals for 570NAT-HW-X19

ELECTRONIC KEYBOARD

Brand: Medeli Pages: 28

Seaboard RISE 25

Brand: Roli Pages: 21

Brand: BH FITNESS Pages: 47

Brand: Casio Pages: 52

Partner ECS430T

Brand: Ectaco Pages: 24

Brand: Alesis Pages: 97

Brand: WeGo Pages: 19

Brand: Korg Pages: 28

Brand: Korg Pages: 378

Brand: Roland Pages: 82

Platinum ProClub

Brand: PaceMaster Pages: 37

Brand: Yamaha Pages: 7

Brand: BLOW VAPOR Pages: 8

BOOKMAN III DBE-1450

Brand: Franklin Pages: 32

Brand: Technics Pages: 96

LTC 8782 Series

Brand: Bosch Pages: 6

Brand: SensFit Pages: 23

Brand: iTaste Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands