evertz 570NAT-HW-X19 User Manual Download Page 12 | Manualshive

Page: 12 / 56

background image

570NAT-HW-X19

High Density Network Address Translator

Page - 2

Revision

1.0

Features & Benefits

• One–to–one NAT with user configurable Packet Replication
• MC–in–MC NAT for tunneling flows based on multicast addresses
• VLAN based NAT for tunneling flows based on VLAN tag
• Port based NAT for tunneling all traffic (ingress/egress) on per port basis
• Port Aggregation (LAN–to–WAN direction)
• Port Redundancy on both WAN and LAN side (network path failure protection)
• Virtual interfaces for Unicast flows mapping or VLAN ID change
• IGMPv3 with SSM support
• Point–to–point and multi–point signal intra/inter–facility distribution/contribution
• Operates over a Dark fiber, Ethernet, IP, MPLS VPLS, core network
• In–band Management (Management Traffic transport over Multicast)
• Support for FEC Pro MPEG (forward error correction)
• 12x 10GbE (SFP10G–TR13–A)
• Control via 570FC Frame Controller
• Full integration with VistaLINK PRO and MAGNUM
• Standalone Web–based control interface

«
...
10
11
12
13
14
...
»

Summary of Contents for 570NAT-HW-X19

























































Reviews:

No comments

Related manuals for 570NAT-HW-X19

MUSIC ACADEMY 16 6125

Brand: Bontempi Pages: 44

Brand: M-Audio Pages: 44

Brand: Korg Pages: 120

Brand: Roland Pages: 56

Smart Coach SB-75

Brand: Canyon Pages: 144

Brand: Velleman Pages: 48

Brand: Roland Pages: 140

yahama PSR - 520

Brand: Yamaha Pages: 104

Clavinova CLP-307

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 72

Brand: Yamaha Pages: 58

Translator 2 Premium

Brand: Vasco Pages: 20

Brand: Kettler Pages: 104

Brand: Octane Fitness Pages: 8

Brand: SIGELEI Pages: 3

Brand: SIGELEI Pages: 3

SWALLOWTAIL 75A

Brand: SIGELEI Pages: 18

Brand: Morrison Bros. co. Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands