EVAPCO ESW4 Rigging And Assembly Instructions Download Page 12

12

ESW4 Closed Circuit Coolers

Optional Sloped Ladders

When sloped ladders are supplied with a unit, they are shipped

 

in the basin section, if there is room. One sloped ladder will be

 

provided for each cell. Assembly is identical for each cell.
Sloped ladders are attached at a minimum of three points.

 

Taller units will have four attachment points. At each point of

 

attachment, the ladder will be fitted with a ladder bracket

 

assembly. The ladder bracket assembly looks like a metal box

 

and is shown in detail (component #4) in Figure 

21

 below. The

 

upper two assembly brackets are factory mounted to the ladder

 

and are not adjustable. These two brackets define the slope of

 

the ladder. The lower brackets are adjustable. See Figures 

22

 

and 

23

 for drawing of the final ladder assembly.

To install the ladder assembly, follow the steps outlined below

 

which refer to Figure

 21

:

1. Remove the ladder bracket mounting bolts 

(A)

from the

ladder mounting channels 

(B)

on pan and casing sections.

2. Loosen, but do not remove, the ladder bracket and

assembly bolts 

(C)

.

3. Slide the ladder bracket assembly 

(D)

over the ladder

mounting channel 

(B)

located on the unit panels. Do not

remove the ladder bracket assembly 

(D)

from the ladder.

4. Align the bolt holes and reinstall the ladder bracket

mounting bolts 

(A)

through the ladder bracket assembly

and the ladder mounting channels 

(B)

.

5. Tighten all bolts.
6. Tighten the adjusting screw 

(E)

in the adjustable mounting

bracket where applicable.

LADDER 

MOUNTING

CHANNEL (b)

ADJUSTING SCREW (e)

(WHEN APPLICABLE)

LADDER BRACKET

MOUNTING BOLTS (a)

LADDER BRACKET

ASSEMBLY BOLTS (c)

LADDER BRACKET

ASSEMBLY (d)

Figure

 21

 

Detail of Ladder, Ladder Bracket Assembly 

and Mounting Channel

NOTE: Upper Section of Unit Must Be Properly Oriented

with Respect to Lower Section. All Mounting Brackets Must

be on Same Side of Unit. Refer to Certified Print For Proper

Orientation.

LADDER SHIPS LOOSE FOR

FIELD MOUNTING (BY OTHERS)

Figure 

22

 

 

End View of Ladder Assembly

ACCESS

 DOOR

Figure 

23

 

 

Side View of Ladder Assembly

Summary of Contents for ESW4

















Reviews: