Euroboor ECO.50S Operator'S Manual Download Page 23 | Manualshive

Page: 23 / 31

background image

23

3.

Precisely mark the center of the hole, and use the tip of the twist drill to position the
machine and in the correct position, with the tip of the twist drill to meet the marked center
of the hole.

Steps 4-12: see chapter Annular cutters. Make sure the machine runs at maximum speed for
twist drills!

5.4 Countersinks

Thanks to its wide range of operating speeds, the machine can also be used for reaming or counter-
sinking.

Follow the steps mention in chapter Twist drills

0800 536 774

[email protected]

www.globalweldingsupplies.com
13 Patiki Road Avondale, Auckland 1026

«
...
21
22
23
24
25
...
»

Summary of Contents for ECO.50S
































Reviews:

No comments

Related manuals for ECO.50S

Brand: Jata electro Pages: 20

Brand: Parkside Pages: 40

Brand: Parkside Pages: 80

Brand: Parkside Pages: 67

Brand: Parkside Pages: 76

Brand: Graphite Pages: 68

Brand: Hilti Pages: 58

Brand: Cook-it Pages: 8

Brand: Dynabrade Pages: 8

Brand: Klarstein Pages: 26

Brand: Klarstein Pages: 32

Brand: Klarstein Pages: 36

Brand: Klarstein Pages: 60

Brand: P.I.T. Pages: 22

Brand: Chicago Electric Pages: 14

Brand: Chicago Electric Pages: 15

Brand: Pantheon Pages: 7

Brand: Pantheon Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands