Euro Appliances EMJG30WSX Use And Care Manual Download Page 5

5

USE

FIG. 3

FIG. 4

FIG. 5

(*) Air inlet - minimum section 100 cm

2

To  use  the  WOK  pan  support  on  Wok  gas
burner only.
Put  it  on  the  WOK  pan  support  and  make
sure of the stability (see fig. A).

Abnormal Operation:
any of the following are considered to be abnormal 
operation and may require servicing:
- yellow tipping of the hob burner flame.
- Sooting up of cooking utensils.
- Burners not igniting properly.
- Burners failing to remain alight.
- Burners extinguished by cupboard doors.
- Gas valves which are difficult to turn.

Fig. A

WARNINGS AND ADVICE FOR THE USER:
- use of a gas cooking appliance produces heat and moisture in the room in which it is installed. The

room must therefore be well ventilated by keeping the natural air vents clear (fig. 3) and by activating
the mechanical aeration device (suction hood or electric fan fig. 4 and fig. 5).

- Intensive and lengthy use of the appliance may require additional ventilation. This can be achieved

by opening a window or by increasing the power of the mechanical exhausting system if installed.

- Do not attempt to change the technical characteristics of the product because it can be dangerous.
-  If  you  should  not  to  use  this  appliance  any  more (or  replace  an  old  model),  before  disposing  of  it,

make it inoperative in conformity with current law on the protection of health and the prevention of
environmental pollution by making its dangerous parts harmless, especially for children who might
play on an abandoned appliance.

- Do not touch the appliance with wet or damp hands or feet.
- Do not use the appliance barefoot.
-  The  manufacturer  will  not  be  liable  for  any  damage  resulting  from  improper,  incorrect  or

unreasonable use.

-  During,  and  immediately  after  operation,  some  parts  of  the  hotplate  are  very  hot:  avoid  touching

them.

- After using the cook top, make sure that the knob is in the closed position and close the main tap of

the gas supply or gas cylinder.

- If the gas taps are not operating correctly, call the Service Department.

Warning:  during  operation  the  work
surfaces  of  the  cooking  area  become
very hot: keep children away!

Summary of Contents for EMJG30WSX

















Reviews: