Euro Appliances EMJG30WSX Use And Care Manual Download Page 16

16

TECHNICAL ASSISTANCE AND SPARE PARTS

Before leaving the factory, this appliance will have been tested and regulated by expert and specialised
personnel in order to guarantee the best performances.
Any  repairs  or  adjustments  which  may  be  subsequently  required  may  only  be  carried  out  by  qualified
personnel with the utmost care and attention.
For this reason, always contact your Dealer or our nearest After Sales Service Centre whenever repairs or
adjustments are required, specifying the type of fault and the model of the appliance in your possession.
Please also note that genuine spare parts are only available from our After Sales Service Centres and a
qualified retail outlets.
The above data are printed on the data label put on the inferior part of the appliance and on the packing
label.
The above informations give to the technical assistant the possibility to get fit spare parts and a heaven-
sent intervention. We suggest to fill the table below.

MARK: ........................................................
MODEL: .....................................................
SERIES: .....................................................

FOR CUSTOMER SERVICE

CALL THE PHONE NUMBER PROVIDED IN

THE WARRANTY.

Summary of Contents for EMJG30WSX

















Reviews: