manualshive.com logo in svg

EUCHNER MGB2-L1, Operating Instructions Manual, Page: 51 / 60

Share
Download
EUCHNER MGB2-L1 Operating Instructions Manual Download Page 51

51

2500233-04-10/21 (translation of the original operating instructions)

Operating Instructions Safety Systems

MGB2-L1…-BR.-… / MGB2-L2…-BR.-… and MGB2-L1…-BP.-… / MGB2-L2…-BP.-…

EN

Reliability values acc. to EN ISO 13849-1

Guard lock monitoring

Control of guard locking

Category

4

4

Performance Level

PL e

PL e

MTTF

D 2)

750

750

years

Diagnostic Coverage DC

99

–

%

PFH

D

2.95 x 10

-9

2.95 x 10

-9

Mission time

20

20

years

Safety Integrity Level

SIL 3

SIL 3

Mechanical life

1 x 10

6

-  In case of use as door stop, and 1 Joule impact 

energy

0.1 x 10

6

B

10D

 (emergency stop)

0.13 x 10

6

Emergency stop

Operating voltage

5 … 30

V

Operating current

1 … 100

mA

Breaking capacity, max.

250

mW

Power supply LED

24

V DC

Controls and indicators

Operating voltage

UB

V

Operating current

1 … 10

mA

Breaking capacity, max.

250

mW

Power supply LED

24

V DC

1)  Values at a switching current of 50 mA without taking into account the cable length.

2)  Fixed failure rate without consideration of faults in wearing parts.

16.1.  Radio frequency approvals

Product description:  Safety Switch
FCC ID: 

2AJ58-03

IC: 22052-03

FCC/IC-Requirements

This device complies with part 15 of the FCC Rules and with Industry Canada’s licence-exempt RSSs. Operation is subject 

to the following two conditions:
1)  This device may not cause harmful interference, and
2)  this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority 

to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of 

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment 

is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if 

not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. 

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required 

to correct the interference at his own expense.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploita-

tion est autorisée aux deux conditions suivantes : 
(1) l’appareil ne doit pas produire de brouillage, et 
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en 

compromettre le fonctionnement.

Summary of Contents for MGB2-L1





























































Reviews:

No comments