EUCHNER MGB2-L1 Operating Instructions Manual Download Page 45

Page: 45 / 60

2500233-04-10/21 (translation of the original operating instructions)

Operating Instructions Safety Systems

MGB2-L1…-BR.-… / MGB2-L2…-BR.-… and MGB2-L1…-BP.-… / MGB2-L2…-BP.-…

15.2. System status table MGB2-BR

Operating mode

Safety inputs FI1A

and FI1B

Door position

Position of the bolt

tongue

Guard locking

Safety outputs FO1A

and FO1B

Door monitoring

output (OD)

Bolt tongue monitoring

output (OT)

Guard lock monitoring

output (OL)

Diagnostic monitoring

output (OI)

LED indicator

Submodule LEDs

State

Power

(green)

STATE

(green)

DIA (red)

Lock

(yellow)

SLOT

(red)

SLOT

(green)

Self-test

OFF

5 Hz

Self-test after power-up

Normal oper

ation

open

not

inser

ted

OFF

long OFF

shor

Normal operation, door open

closed

not

inser

ted

OFF

long ON, shor

OFF

Normal operation, door closed

OFF

closed

inser

ted

OFF

long ON, shor

OFF

long ON, shor

OFF

Normal operation, door closed, bolt tongue inser

ted, safety inputs FI1A/

FI1B OFF

closed

inser

ted

OFF

long ON, shor

OFF

long ON, shor

OFF

ith active guar

d lock monitoring:

normal operation, door closed, bolt

tongue inser

ted. Safety inputs FI1A/FI1B ar

e ON. Safety outputs FO1A and

FO1B

e OFF

ith inactive guar

d lock monitoring:

normal operation, door closed, bolt

tongue inser

ted. Safety inputs FI1A/FI1B ar

e ON. Safety outputs FO1A and

FO1B ar

e ON

OFF

closed

inser

ted

OFF

long ON, shor

OFF

Operation in a BR chain:

normal operation, door closed and locked.

Safety outputs on the pr

evious device OFF

closed

inser

ted

OFF

Operation as separate device:

normal operation, door closed and locked

Operation in a BR chain:

normal operation, door closed and locked.

Safety outputs on the pr

evious device ON

Teach-in standby

(only for MGB2 unicode)

not

inser

ted

OFF

3 x

Door open; device is r

eady for teach-in of another handle module (only 3

min. after power-up). If a transponder is detected, jump to the teach-in operation state. Should the teach-in operation not be successful, this state is active again after a r

eset.

Setup

(only for MGB2 unicode)

OFF

5 Hz

aiting for addr

ess assignment by master

closed

inser

ted

OFF

1 Hz

Tip for teach-in operation: to pr

event the interruption of teach-in operations,

close door and switch on guar

d locking.

If teach-in operation is star

ted, it is always continued to the end. After the

teach-in time has elapsed, one of these states is assumed with latching: 1. User action acknowledgment 2. T

each-in err

3. T

ransponder err

OFF

1 Hz

Positive acknowledgment after completion of teach-in operation

Summary of Contents for MGB2-L1





























































Search results

Summary of Contents for MGB2-L1

Reviews:

EUCHNER MGB2-L1, Operating Instructions Manual, Page: 45 / 60

Search results

Summary of Contents for MGB2-L1

Reviews: