manualshive.com logo in svg

EUCHNER MGB2-L1, Operating Instructions Manual, Page: 19 / 60

Share
Download
EUCHNER MGB2-L1 Operating Instructions Manual Download Page 19

19

2500233-04-10/21 (translation of the original operating instructions)

Operating Instructions Safety Systems

MGB2-L1…-BR.-… / MGB2-L2…-BR.-… and MGB2-L1…-BP.-… / MGB2-L2…-BP.-…

EN

8.4.  Escape release (optional)

The escape release is used to open a locked guard from the inside without tools.

DIP

OFF

ON

When release monitoring is active, the system enters into a latching fault when the escape release is actuated.

See 

System status table

, 

signal sequence incorrect

 status (DIA red, Lock flashes 1 time).

The system might not enter into a latching fault if the escape release is actuated very slowly.

Important!

 

Ì

It must be possible to actuate the escape release manually from inside the protected area without 

tools.

 

Ì

It must not be possible to reach the escape release from the outside.

 

Ì

The bolt tongue must not be under tensile stress during manual release.

 

Ì

The escape release meets the requirements of Category B according to EN ISO 13849-1:2015.

 

Ì

The correct function must be checked at regular intervals.

 

Ì

Observe the notes on any enclosed data sheets.

 

Ì

Fit escape release such that operation, inspection and service are possible.

 

Ì

The actuation axis for the escape release must be inserted min. 9 mm into the handle module. Note the information on 

the different profile widths in chapter 

8.4.1. Preparing escape release on page 20

.

 

Ì

Adjust escape release axis at right angles to the handle module. See 

Fig. 10

.

Summary of Contents for MGB2-L1





























































Reviews:

No comments