manualshive.com logo in svg

EUCHNER CES-AH-C03-AE-LS, Operating Instructions Manual

Share
Download
EUCHNER CES-AH-C03-AE-LS Operating Instructions Manual Download Page 14

Operating Instructions

Non-Contact Safety Switch CES-AH-C03-AE-LS

14

(Translation of the original operating instructions) 2105267-10-08/20

9.3.  Functional check

After installation and any fault, the safety function must be fully checked. Proceed as follows:

WARNING

Danger of fatal injury as a result of faults in installation and functional check.

 

Ì

Before carrying out the functional check, make sure that there are no persons in the danger zone.

 

Ì

Observe the valid accident prevention regulations.

1.  Switch on operating voltage.

 

Ì

The safety switch carries out a self-test.  

The green STATE LED flashes for 3 s at 10 Hz. 

The green STATE LED then flashes at regular intervals.

2.  Close all guards.

 

Ì

The machine must not start automatically.

 

Ì

The green STATE LED illuminates continuously.

3.  Enable operation in the control system.
4.  Open the guard.

 

Ì

The machine must switch off and it must not be possible to start it as long as the guard is open.

 

Ì

The green STATE LED flashes at regular intervals.

Repeat steps 2-4 for each guard.

Summary of Contents for CES-AH-C03-AE-LS

























Reviews:

No comments

Brands by name

Popular brands

Load more brands