eTung MR-900T User Manual Download Page 30

Page: 30 / 76

MR-900T User Manual

25)

AT+SMSZHUANFA=txt,info_src,dest

Ask the router to send an SMS to info_src first with content
“txt” (only in English characters and digits), and then forward

the reply to dest. dest can be omitted, and if then the reply will

be forwarded to the mobile that sends this AT command. If the
reply SMS has more than one message, the router will forward

the messages one by one.

For example: AT+SMSZHUANFA=CXLL,10086,13801234567,
means to send an SMS to 10086 to query traffic and then

forward the reply to 13801234567.

MR-900T V1.4.9 or higher versions additionally support the

following remote AT commands:

26)

AT+VIRHUB&TAP_IP?

Check the remote access IP address via Virhub, with reply:

OK:x.x.x.x

27)

AT+VIRHUB&TAP_MASK?

Check the remote access netmask via Virhub, with reply:
OK:x.x.x.x

28)

AT+VIRHUB&TAP_IP=x.x.x.x

Set the remote access IP address via Virhub, with reply OK.

29)

AT+VIRHUB&TAP_MASK=x.x.x.x

Set the remote access netmask via Virhub, with reply OK.

MR-900T V2.0.8 or higher versions additionally support the

following remote AT commands:

30)

AT+SIMID

Check SIM card's IMSI and CCID

31)

AT+CELLID

Check base station's location number and cell code.

32)

AT+OPER

Check operator's name

Summary of Contents for MR-900T













































































Search results

Summary of Contents for MR-900T

Reviews:

Brands by name

Popular brands

eTung MR-900T, User Manual

Search results

Summary of Contents for MR-900T

Reviews:

Brands by name

Popular brands