manualshive.com logo in svg

Etel DSC2P, Hardware Manual, Page: 42 / 44

Share
Download
Etel DSC2P Hardware Manual Download Page 42

ETEL Doc.- Hardware Manual # DSC2P / Ver H / 6/1/11

DSC2P Hardware Manual

41

3.9

LEDs meaning

The different LEDs present on the controller have the following meaning:

Remark:

The green LED 'SERVO ON' and the red LED cannot be ON together.

Remark:

The power supply's LEDs are present on the DSC2P housed format and on the DSO-PWS
supplying the DSC2P rack format.

LED

Status

Meaning

Green LED 'TEB OK'

ON

The communication through the TEB is running

OFF

The communication through the TEB is not running => check the wiring or/and the master

Green LED 'SERVO ON'

ON

Controller without error

OFF

Controller in error or not ON

Red LED

ON

Controller in error => check monitoring M64

OFF

Controller without error

LED regarding the        

power supply

Status

Meaning

Green LED 

'POWER VOLTAGE'

ON

If the red LED is off, both power and auxiliary supply are switched on
If the red LED is on, only the power supply input is switched on

OFF

If the red LED is off, only the auxiliary supply input is switched on

Red LED 'POWER ERROR'

ON

If the green LED is on, only the power supply input is switched on

OFF

If the green LED is on, both power and auxiliary supply are switched on
If the green LED is off, only the auxiliary supply input is switched on

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for DSC2P













































Reviews:

No comments