background image

Irideon WLZ User Manual

3

IMPORTANT SAFEGUARDS

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS

Keep lamp away from materials that may burn.

External temperature after 5 minutes of full-brightness
operation: 27°C (81°F).

External temperature when steady state is achieved: 50°C (122°F).

SAVE THESE INSTRUCTIONS

Canopy Fixture

WARNING:

RISK OF ELECTRIC SHOCK! Power must be off

when you perform this procedure.

The fixture must be installed by a qualified electrician in
accordance with all national and local electrical and
construction codes and regulations.

AVERTISSEMENT :

RISQUE DE DÉCHARGE ÉLÉCTRIQUE!

L'alimentation doit étre éteinte avant d'exécuter cette
procédure.

Track-Mount Fixture

WARNING:

To reduce the risk of fire and electric shock, use

the track-mount fixture only with the DataTrack (EUTRAC)
track system.

AVERTISSEMENT :

Pour éviter le risque d'incendie ou de

choc électrique avec le modèle adaptateur pour rail, utiliser
uniquement avec une alimentation par rail DataTrack
(EUTRAC).

WARNING:

Use the track-mount fixture with ceiling-

mounted track only.

Summary of Contents for Irideon FPZ





























Reviews: