background image

ETC Installation Guide

ColorSource CYC v1.7/v3.1

Safety

For professional use only. Read the entire manual before using this
equipment.

WARNING:

Risk of eye injury. Do not stare directly into the light.

Do not mount the fixture on or near a flammable
surface.

Disconnect the fixture from power and DMX and allow it
to cool before installing accessories or performing any
cleaning and maintenance.

AVERTISSEMENT :

Risque de lésion oculaire. Ne fixez pas directement la
lumière.

Ne pas installer le projecteur sur ou à côté d’une surface
inflammable.

Débranchez le projecteur de son alimentation et du
DMX et laissez-le refroidir avant d’installer des
accessoires ou d’effectuer un nettoyage ou un entretien.

WARNING:

RISK OF ELECTRIC SHOCK! The light source in

this luminaire is not user-replaceable, and must be replaced
only by a qualified technician. Contact ETC Customer Support
for assistance.

AVERTISSEMENT :

RISQUE DE DÉCHARGE ÉLÉCTRIQUE! La

source lumineuse de ce projecteur n'est pas remplaçable par
l'utilisateur et ne doit être remplacée seulement par un
technicien qualifié. Contactez le service client ETC pour
obtenir de l’assistance.

ColorSource CYC

Page 2 of 12

ETC

Summary of Contents for ColorSource CYC













Reviews: