background image

ET C

®

,   S o u rc e   F o u r

®

,   S o u r c e  4

W R D

,   P A RN e l

®

,   S e n s o r

®

,   a n d 

U n i s o n

®

  a re   e i t he r   r eg i s t er ed   t r ad e m a r k s   o r   t r a d e m a rk s   o f  

E l e ct r o n i c   T h e a t re   Co n t r o l s ,   I n c.  i n   t h e   U n i t e d   S t a t e s   a nd   o t h e r  
c o u nt r i e s .

A l l   o t h e r   tr a d e m a r k s ,   b o t h   m a r k e d   a n d   n o t   m a r k e d ,   a r e   t h e  
p r o p e r t y   o f   t h e ir   r e s p e c t iv e   o w n e r s .

T h i s   p r o d u ct   i s   p ro t e c te d  b y  o n e  o r   m o r e   of   t h e   fo l l o w i n g  
U . S . P a t e n ts :   U S   9, 2 6 1 , 2 4 1   a n d  9 , 2 7 3 , 8 3 1 .

E T C  i n t e n d s   t h i s   d o c u m e n t ,   w h e t h e r   p r i n te d   or   e l e c t ro n i c ,  t o   b e  
p r o vi d e d   i n   i t s   e nt i r e ty .   T h is   p r o d u c t   i s   i n t e n d e d  f o r  
p r o fe s s i o n a l   u s e   o n l y .   R e a d  t h i s   e n t ir e   d o c u me n t   b e f o r e   u s i n g  
t h i s   p r o d u c t .  

Summary of Contents for Source 4WRD

























Reviews: