ESI RF BRIDGE User Manual Download Page 16

Page: 16 / 19

ESI RF BRIDGE

User Guide

version 1.0.4.0

www.elec-solutions.com

Page 16 of 19

Query Which Channels a SUITE Remote Controls

Use this menu item to find out the channel assigned to each button on a SUITE remote.

As each SUITE remote is joined to the network, the ESI RF Bridge assigns a channel to each button on the
remote, in ascending order, from channel 1 to channel 31.

IMPORTANT

: The ESI RF Bridge has a maximum of 32 channels available (0 through 31 = 32). Channel 0

is the ALL channel.

For example, if the first remote joined is an Arc remote (4 buttons), then the assignment is:

Button 1 gets

Channel 1

Button 2 gets

Channel 2

Button 3 gets

Channel 3

Button 4 gets

Channel 4

If the next remote joined is a Step remote (1 button), then the assignment is:

Button 1 gets

Channel 5

If the next remote joined is an Arc remote (4 buttons), then the assignment is:

Button 1 gets

Channel 6

Button 2 gets

Channel 7

Button 3 gets

Channel 8

Button 4 gets

Channel 9

and so on.

NOTE:

If enough remotes are joined, so that a channel assignment past channel 31 is needed,

all

remotes joined

after channel 31 will get one of the following default assignments. Any channel assignment can be
changed using the Device Menu in the ESI RF Bridge

— do this only after all remotes/motors have joined.

SUITE Arc remote:

Button 1 gets

Channel 1

Button 2 gets

Channel 2

Button 3 gets

Channel 3

Button 4 gets

Channel 4

SUITE Step remote:

Button 1 gets

Channel 1

2. Manage Channels

Use this menu to Enable, Disable, or Query channels on motors.

Summary of Contents for RF BRIDGE




















Search results

Summary of Contents for RF BRIDGE

Reviews:

Related manuals for RF BRIDGE

Brands by name

Popular brands

ESI RF BRIDGE, User Manual

Search results

Summary of Contents for RF BRIDGE

Reviews:

Related manuals for RF BRIDGE

Brands by name

Popular brands