manualshive.com logo in svg

ESI RF BRIDGE, User Manual

Share
Download
ESI RF BRIDGE User Manual Download Page 10

ESI RF BRIDGE   

 

 

 

 

 

User Guide 

 

 

 

 

 

 

version 1.0.4.0

 

 

www.elec-solutions.com 

 

 

 

 

© 2014 Electronic Solutions, Inc. 

 

 

 

 

Page 10 of 19 

 

Regulatory Compliance 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not 
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause 
undesired operation. 
 
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation 
est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit 
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. 
 
This Class B digital apparatus complies with Canadian ICES-003. 
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may 
cause undesired operation of the device. 
 
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC 
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not 
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the 
following measures: 
—Reorient or relocate the receiving antenna. 
—Increase the separation between the equipment and receiver. 
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
—Consult the dealer or an experienced radio/TV technician for help. 
 
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to 
operate the equipment. 

 

If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be 
impaired. 

 

FCC ID:

 P7RRFBRIDGE 

This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to part 15 of the FCC Rules. 

IC:

 7206A-RFBRIDGE 

This Class B digital apparatus complies with Canadian ICES-003. 

 

This symbol means that this product complies with the European Union Harmonised 
Standards for the Low Voltage Directive and EN 60335-1: 2012 

 

This symbol means that this product complies with International Standard EN 55011: 2007 
and AS/NZS 4268: 2008 

 

This symbol cautions the user to refer to all of the instructions and warnings specified in the 
User Guide and the Installer’s Manual & Instructions before using this product. 

 

This symbol indicates an RS-232 port. 

 

This symbol means that this product must be disposed of separately from household waste 
and must be disposed of according to local laws and regulations for electrical and electronic 
waste. 

 
 

 

Summary of Contents for RF BRIDGE




















Reviews:

No comments

Brands by name

Popular brands

Load more brands