![background image](http://html1.mh-extra.com/html/escort/max-ci-360/max-ci-360_installation-manual_2426272006.webp)
GPS Antenna
Yellow Shrink
1
Determine the best location for the GPS
antenna. The GPS Antenna requires a clear
view of the sky. The magnetic base can be used
on most vehicles to mount to the roof of the
car or the trunk lid. It can also be mounted to
the dashboard or rear deck using double-sided
tape.
2
Mount the GPS Antenna, being sure that
roof racks or other obstructions do not block
its view of the GPS satellites.
3
Locate a suitable entry point into the
vehicle. Refer to the Installation Tips section for
locating a suitable entry point.
4
Route the cable through the entry point and
secure along its path. If mounting near the
front or rear window, it is usually possible to
tuck the cable under the gasket surrounding
the glass.
5
Once inside the vehicle’s interior, route the
cable to the Interface and plug into the
connector labeled “GPS.”
6
Secure and conceal the cable under interior
trim panels.
Display Bezel Mounting
1
The supplied display bezel can be used to
mount the Display permanently in the dash or
console.
2
Determine the best location for the Display
Module. If installed by a professional, the
customer should be consulted. A flat, plastic
surface with no obstructions behind it is best
for this type of mounting.
3
Cover the mounting surface with masking
tape to prevent accidental scratches.
4
Using the supplied hole template, mark the
location.
5
Ensure there are no hidden cables, brackets,
or other components behind the location, and
that there is adequate clearance behind the
panel. The Display will protrude into the dash
or console by 1/2".
6
Very carefully cut the hole in the mounting
surface.
7
Feed the display module cable through the
bezel and the opening in the dash then route it
to the interface.
8
Remove the masking tape protecting the
trim panel.
9
Clean the mounting surface thoroughly.
10
Apply the double-sided adhesive tape to
the display bezel.
11
Mount the Display Module using the bezel
adhesive.
12
Plug the connector into the Interface
connector labeled “Display Module.”
13
Secure and conceal the cable under trim
panels.
10
11
E
Front Laser ShifterMax
Sensors
(Continued)
1
Snap mounting bracket onto sensor and
install the included bolts but do not tighten
them. If the bolts do not thread into the sensor
then you have the bracket on backwards.
2
Apply the double sided tape to the
underside of the sensor’s mounting bracket.
Check front alignment and mount the sensor
to a solid surface of the vehicle.
3
Use the supplied bubble level to ensure the
sensor is parallel to the road and tighten the
sensor’s mounting bracket bolts.
4
Repeat for additional sensor(s).
Securing Connectors with Shrink Tube
Once you’ve installed all components properly
and tested to ensure all parts are working
properly, use cable ties to fasten sensor cables
to a solid surface, keeping them away from
heat and any moving parts. It is advisable to
use the supplied heatshrink tubes to protect
connectors against water, moisture, dust, etc.
IMPORTANTLY the ShifterMax sensors are
shipped in “receive only” mode. Shifting
must be enabled in the bands settings. See
the Preferences section of the Owner’s
Manual.
Additional ShifterMax Sensors
• ESCORT MAX CI users wanting to add rear
sensors, two (2) additional ShifterMax
Sensors with included hardware are sold
separately.
Display Module
Orange Shrink
1
Determine the best location for the Display
Module. If installed by a professional, the
customer should be consulted. An optimal
location is clearly visible from the driver’s
position and does not take a driver’s eyes off
the road for more than a moment.
2
Clean the mounting surface thoroughly.
3
Mount the Display using the pre-applied
adhesive.
4
Route the cable to the Interface and plug
into the connector labeled “Display Module.”
5
Secure and conceal the cable under trim
panels.
F