EROAD ehubo2 Installation Manual Download Page 6

7

RAM

RAM

TAPE MOUNT

• Clean flat surface with alcohol wipe

• Fit mounting plate 

(A)

 to mount using 

counter sunk screws/holes and nuts

 (D)

• Apply adhesive tape 

(B)

 to mounting 

plate and firmly press to surface

PERMANENT MOUNT

 

Attach mount to dash 

using mounting plate

 

(A)

screws and nuts 

(E)

.

or

Attach Ehubo2 to the mount  

using screws and washers 

(C)

Use of the washers is essential to 

reliably secure the Ehubo2!

Route the Ehubo2 wiring out of 

the way and down the back of 

the dashboard. 

NOTE: If swapping mounting option do not re-use nyloc nuts, use unused nuts as supplied.

Insert the two rear hatch security plugs. The plugs are keyed and only fit in 

their correct position. Proceed with 

2A

 

PERMANENT MOUNT

 (dashboard) or 

2B TAPE MOUNT

 (windscreen or flat surface).

1

2B

2A

A

A

B

3

4

Mount the Ehubo2

C

E

The Ehubo2 can be mounted on the dashboard or windscreen (where permitted by law 
where the vehicle is being operated). For windscreen mount or temporary installation on a 
flat surface please use the adhesive tape supplied.

NOTE:

 Choose the mounting location for your Ehubo2 carefully and ensure that it complies 

with all local regulations. Make sure that the Ehubo2 does not impair the driver’s visibility, 
does not pose a risk in the event of an accident, does not interfere with any systems used 
in the operation of the vehicle, does not block or impair the deployment of the airbag, and 
has a good view of the sky. Choose a location that does not expose the Ehubo2 to excessive 
temperature or vibration.

D

Summary of Contents for ehubo2
















Reviews: