manualshive.com logo in svg

Ergoswiss 901.20034, Operating Instruction

Share
Download
Ergoswiss 901.20034 Operating Instruction Download Page 4

 

 

 

Operating instruction 

Spindle lifting system SL/SK/SM 14xx Compact 

 

 

Document no.: B-00061 

Edition 2022 05

 

Operating instruction EN 

Copyright by Ergoswiss AG

 

Page 

4

 of 

26

 

 

1

 

Safety requirements 

The safety instructions must be paid attention to! If the system is operated improperly or not in accordance 

with the intended use, there may be a risk to persons and property! 

 

Before installing and operating the lifting system, this operating instruction must be read and understood. 

The manual must be kept in the close proximity to the system for future reference. 

 

1.1

 

Explanations of the symbols and notes 

The following explanations of symbols and notes must be observed. These are classified according to ISO 

3864-2 (ANSI Z535.4). 

 

DANGER 

 

Indicates an imminent danger. 

Failure to follow the information will result in death or severe physical injury (disability). 

 

WARNING 

 

Indicates a potentially dangerous situation. 

Failure to follow the information will result in death or severe physical injury (disability). 

 

ATTENTION 

 

Indicates a potentially dangerous situation. 

Failure to follow the information will result in damage to property and minor or medium  

physical injuries will result. 

 

 

NOTE 

Indicates general information, useful user tips and work recommendations, which have no im-

pact on the health and safety of staff. 

 

 

 

 

Summary of Contents for 901.20034



























Reviews:

No comments

Brands by name

Popular brands

Load more brands