Ergoswiss 901.20034 Operating Instruction Download Page 24

Page: 24 / 26

Operating instruction

Spindle lifting system SL/SK/SM 14xx Compact

Document no.: B-00061

Edition 2022 05

Operating instruction EN

Page

9.5

Error codes on the display

Display

Cause

Trouble shooting

The control box compact is equipped

with an overheating protection.

This overheating protection will activate

due to too high temperatures

Wait until the control box has cooled down and the

message

«HOT»

is no longer displayed.

Then the control box is ready for operation again.

There is an internal error at the control

box.

Proceed according to the following error list.

blinking

000

Motor position lost

Perform a «Long Key Down».

Internal error channel 1

Disconnect the power cable from the mains and

contact the customer service.

Internal error channel 2

Defective channel 1

Insert the motor cable correctly.

Defective channel 2

Excess current motor M1

System overloaded

→

Remove load from the system

System jammed

→

remove clamped object

Excess current motor M2

Excess current motor group 1

Excess current motor group 2

Collision protection

Excess current at the control

Plug detection at motor socket M1

Plug in the motor cable correctly at the respective

socket.

Perform a Factory reset «S 0».

Plug detection at motor socket M2

Motor replaced

Synchronising of the motor group 1

impossible

Remove load from the system.

Perform a Factory reset «S 0».

Contact the customer service if the error remains

displayed.

Synchronising of the motor group 2

impossible

Too high voltage

Disconnect the power cable from the mains.

Contact the customer service.

Change of the drive configuration

Disconnect the power cable from the mains and

wait at least for 5 seconds.

Reconnect the power cable.

Perform a Factory reset «S 0».

Internal error

Disconnect the power cable from the mains and

wait at least for 5 seconds.

Reconnect the power cable.

Perform a Factory reset «S 0».

Contact the customer service if the error remains

displayed.

Connection error while synchronising

The error is displayed for 15 seconds,

then the control box changes to the re-

set mode with a flashing display of

«000»

Disconnect the power cable from the mains and

wait at least for 5 seconds.

Reconnect the power cable.

Perform a Factory reset «S 0».

Summary of Contents for 901.20034



























Search results

Summary of Contents for 901.20034

Reviews:

Brands by name

Popular brands

Ergoswiss 901.20034, Operating Instruction

Search results

Summary of Contents for 901.20034

Reviews:

Brands by name

Popular brands