ERGONOMIC SOLUTIONS 2ESP-WA-C48-BLK Instructions Manual Download Page 8

Page: 8 / 12

STEP 11

Attach the release lever at the front of the table
on the left or right side for easy access by the user.

• Use four #8x½ screws to attach

the lever to the underside of the
worksurface.

• Slide the cable clip over the release

lever cable. Position the clip to support

the cable from sagging and attach
it with the remaining #8x½ screw.

IMPORTANT:

When securing the cable,

the cable should be gently curved to
ensure smooth operation. Do not kink
the cable or form corners with it.

STEP 12

IMPORTANT:

There must be 1" (25mm) of clearance on all sides of the worksurface (and other moving parts)

to ensure free, unobstructed movement.
• Adjust the leveling glides on the feet to level the worksurface, if necessary.
•

is important when testing operation.

WEIGHT ADJUSTABLE ESPREE PNEUMATIC TABLE BASE

ASSEMBLY

Place all contents that will be used

on the worksurface before testing

operation. Examples:
• Monitor(s)
• Keyboard
• Mouse
• Laptop
• Docking station
• Light

Note:

If you plan to install a keyboard tray please

attach the release lever on the left side of the

worksurface to avoid cross over issues.

Cord

Clip

Summary of Contents for 2ESP-WA-C48-BLK












Search results

Summary of Contents for 2ESP-WA-C48-BLK

Reviews:

Brands by name

Popular brands

ERGONOMIC SOLUTIONS 2ESP-WA-C48-BLK, Instructions Manual

Search results

Summary of Contents for 2ESP-WA-C48-BLK

Reviews:

Brands by name

Popular brands