manualshive.com logo in svg

ERGONOMIC SOLUTIONS 2ESP-WA-C48-BLK, Instructions Manual

Share
Download
ERGONOMIC SOLUTIONS 2ESP-WA-C48-BLK Instructions Manual Download Page 6

6

Right-Side

Column

Left-Side

Column

M8x40

5mm

Allen Key

M8x40     

5mm

Allen Key

WEIGHT ADJUSTABLE ESPREE PNEUMATIC TABLE BASE 

ASSEMBLY

STEP 6

Change the length of the adjustable feet, if necessary.
• The length of the feet may be either 22" (55.9cm) or 28" (71.2cm). The feet are shipped in the 28" length.
• 

four base screws, and the 3mm Allen key for the two smaller screws.

• Slide the feet to the 22" length and reinstall the four screws with the 5mm Allen key.

STEP 7

Attach a foot to each of the legs.  
Refer to the illustrations.
• The left side foot is attached with  

four M8x40 screws using the 5mm  
Allen key.

• The right side foot is attached with  

three M8x40 screws and one  
M8x25 screw. The M8x25  

 

insert on the leg column.  
Tighten it with a 5mm Allen key.

Adjustment

Plate

5mm

Allen Key

Slide In

22"

Adjustable

Length

28"

3mm

Allen Key

M8x25

Summary of Contents for 2ESP-WA-C48-BLK













Reviews:

No comments

Brands by name

Popular brands

Load more brands