ERGONOMIC SOLUTIONS 2ESP-WA-C48-BLK Instructions Manual Download Page 4

Page: 4 / 12

WEIGHT ADJUSTABLE ESPREE PNEUMATIC TABLE BASE

ASSEMBLY

STEP 3

Remove the cover by releasing the two hooks from the cut-outs.

STEP 4

Secure the legs in the vertical position with the four M8x14 screws.
• Use the 5mm Allen key.

— Align the hole on each side of the leg column with the hole in the frame channel by rotating the leg

column.

• If necessary, use the 10mm hex bit to rotate the square drive rod to gain access to the left rear screw

hole.
— The hex adjustment is located on the side of the top support, as shown.
—

Remove Cover

leg column and the hole in the frame channel is most easily done by inserting the Allen key through
the hole in the frame channel and the hole in the leg column. Then hold the leg in place and drive
the screw.

Rotate the bit clockwise only. (Do not go below 0-0 on the gauge; do not rotate the bit

counterclockwise.)

Note:

A small spacer or box may be helpful to hold the frame in the proper position. The alignment of the

M8x14

Front

Rear

Rotate Square Drive Rod,

If Necessary to Install Screw

10mm

Hex Bit

Summary of Contents for 2ESP-WA-C48-BLK












Search results

Summary of Contents for 2ESP-WA-C48-BLK

Reviews:

Brands by name

Popular brands

ERGONOMIC SOLUTIONS 2ESP-WA-C48-BLK, Instructions Manual

Search results

Summary of Contents for 2ESP-WA-C48-BLK

Reviews:

Brands by name

Popular brands