manualshive.com logo in svg

Epygi QUADRO E1, Administrator'S Manual, Page: 26 / 87

Share
Download
Epygi QUADRO E1 Administrator'S Manual Download Page 26

QuadroE1/T1 Manual II: Administrator's Guide   

Administrator's Graphical User Interface 

 

QuadroE1/T1;  (SW Version 3.0.x) 

26 

Firmware Update 

This window allows to update the software of Quadro by installing new firmware called image. Users registered at Epygi will receive a notice when 
new firmware is available and will be able to download it from the Epygi Technical Support WEB page.  

Updating a new firmware requires a perfectly working power supply. Therefore Quadro is provided with a battery (accumulator). If the battery is low 
or simply absent the “There is no battery or voltage is low” warning is displayed

 

 

Please Note:

 Installing new firmware will take about 15 minutes. 

During this time, the QuadroCS, telephony and Internet access 
will be disabled. 
The firmware update will cause the loss of the following data: 

•

 

DHCP leases

 

•

 

Transfer

 

statistics

 

•

 

Call statistics

 

•

 

All

 

pending

 

events

 

•

 

User

 

specific

 

GUI

 

states

 

•

 

All

 

custom (user recorded) voice messages

 

The following main processes will be stopped during the 
firmware update and will be restarted afterwards: 

•

 

Voice

 

Software

 

•

 

Network

 

Time

 

Protocol

 

Daemon

 

•

 

Network

 

Interface

 

Statistic

 

Daemon

 

Please Note:

 If you consider the 

218H

Call

 

Statistics

 entries in the 

displayed tables to be important, it is recommended to download 
them from the corresponding page prior to starting the Firmware 
Update. 

Next will move you to the second page of Firmware Update 
where the image file should be selected. 

 

Fig. II-34: Firmware Update page 1 

The second page of Firmware update has the Browse button 
used to browse the image file, and the Specify Image text field 
that will display the selected image filename. 

Pressing  Save will start uploading the image file to the board. 
The next page will be displayed, showing the result of a 
verification of the image being burned. 

 

 

Fig. II-35: Firmware Update page 2

This page displays non-editable information about the image 
validity. The Image Check will display invalid if the image does 
not correspond to the hardware version. 

The fields Current Software Version and New Software 
Version show the old software version and the version of the 
new image. 

This page needs a confirmation to continue image updating. If 
you are sure that the image version is appropriate for your 
device press Save. 

 

 

Fig. II-36: Firmware Check page 

 

 

 

Summary of Contents for QUADRO E1
























































































Reviews:

No comments