Epson Stylus Photo 720 Service Manual Download Page 90

Page: 90 / 154

EPSON Stylus Photo 720 / EPSON Stylus Photo EX3

Revision A

Disassembly and Assembly

Disassembly

4.2.5.9 PE Sensor Assembly Removal

Remove the Housing. (See “Housing Removal” on page 68)

Remove the ASF Assembly. (See “ASF Assembly Removal” on page 80)

Release 2 PE Sensor Assembly Securing Hooks from the Top Frame Cutoffs and
remove PE Sensor Assembly by sliding it upward.

Figure 4-42. PE Sensor Assembly Removal

Figure 4-43. PE Sensor Lever Head Setting Position

After releasing two hooks, remove the PF Sensor

Assembly, sliding it upward.

(From back side of the

frame)

PE Sensor-Holder

This side should be

installed on the

frame.

Torsion Spring 0.22

PE Sensor Lever

PE Sensor Board Assembly

C H E C K

P O I N T

When installing the PE Sensor Assembly, make sure that the sensor
lever is correctly inserted into the hole of Paper Guide Assembly.

Right Paper Guide Top Assembly

PE Sensor Lever Head

Summary of Contents for Stylus Photo 720



























































































































































Search results

Summary of Contents for Stylus Photo 720

Reviews:

Related manuals for Stylus Photo 720

Brands by name

Popular brands

Epson Stylus Photo 720, Service Manual

Search results

Summary of Contents for Stylus Photo 720

Reviews:

Related manuals for Stylus Photo 720

Brands by name

Popular brands