Epson Stylus Photo 720 Service Manual Download Page 54

Page: 54 / 154

EPSON Stylus Photo 720 / EPSON Stylus Photo EX3

Revision A

Troubleshooting

Unit Level Troubleshooting

3.2 Unit Level Troubleshooting

You can identify the troubles, using flowcharts in this section and then find defective
unit. When you find out defective unit, refer to “Unit Repair (Printer Mechanism)” to
find defective components and replace them.

3.2.1 Printer does not operate at power on

Flowchart 3-1.

Table 3-4. Symptoms and Problems

Symptom

Problem

Flowchart No.

Printer does not operate at
power on.

LEDs do not light.

Printer mechanism does not operate.

Flowchart 3-1

Error is detected

Error is indicated by LED indication.

Flowchart 3-1

Failure occurs during
printing.

Printing is not performed.

Abnormal printing (dot missing, etc.)

Print quality is poor.

Flowchart 3-1

Printer does not feed paper
correctly.

No paper is fed.

Paper feed is irregular.

Paper jam occurs.

Flowchart 3-1

Control panel operation is
abnormal.

No response to button access.

Flowchart 3-1

Start

Yes

End

Replace the fuse,
disconnect CN10 on
MAIN board, and
turn on power.

Check the output
voltage of CN2 on
the power supply.

Replace the MAIN
board.

Check the motors,
printhead, and
other components.

Replace the power
supply.

Summary of Contents for Stylus Photo 720



























































































































































Search results

Summary of Contents for Stylus Photo 720

Reviews:

Related manuals for Stylus Photo 720

Brands by name

Popular brands

Epson Stylus Photo 720, Service Manual

Search results

Summary of Contents for Stylus Photo 720

Reviews:

Related manuals for Stylus Photo 720

Brands by name

Popular brands